Not sure who else to ask...
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=170848
Printed Date: 31 Oct 2025 at 5:01am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: Not sure who else to ask...
Posted By: Buckyman
Subject: Not sure who else to ask...
Date Posted: 05 May 2020 at 10:48pm
| I've been looking and looking trying to learn about a manure pump(like the patz 1512) since my dad has used one for years and I would like to put one in my barn so i don't have to haul every day and all the management associated with that. Dad had a badger bn122 pump which seems to not exist on the internet and the patz pump is the only new one like it that I've found...does anyone know what it would cost to install such a machine?? Anyone know of other companies still making them?? |
Replies:
Posted By: Tenn allis
Date Posted: 06 May 2020 at 5:29am
| Never used a piston pump like that before always used a propeller type pump. Company such as GEA or jamesway still make them I’m sure. There is a company called N-Tech that might make a pump like that. Google any of them and get some contact information |
Posted By: Buckyman
Date Posted: 06 May 2020 at 12:55pm
| This pump is designed to go inside the barn and "flush" slurry manure out of the tank it has and through a big plastic pipe into a manure pit. Apparently they were popular in "mole hill" systems as my grandpa has said before. That's where someone who would usually haul daily pours a cement pad outside the barn and uses this pump to push manure and bedding up through a hole in the center of the pad to make their manure pile instead of hauling it every day or physically hauling manure out to a pile. I'm willing to bet almost nobody knows what these are cuz my dad is one of two people that I know that has one and the other guy I'm not even sure if he has the same type of pump... |
Posted By: Stacik
Date Posted: 06 May 2020 at 7:13pm
| Tech makes a piston pump but the ones I like are made by Zabel they use a hydraulic cylinder instead of a gear box. |
Posted By: steve(ill)
Date Posted: 06 May 2020 at 7:35pm
|
I worked at a Electrical Power PLant with a coal ash pond.. WE had SLURRY pumps that were electric or hydraulic operated. The PUMP was an impeller type pump. The could pump 50% solids as long as some water was present. They would pump chunks / rocks up to 2 inches in diameter.... You might consider that..... I saw one hanging on the bucket of an excavator once... They lowered it slowly into a ash pond with 6 inches of water on top. It ate a hole 2 ft in diameter and 10 ft deep in a couple minutes... look up SLURRY PUMP. ------------- Like them all, but love the "B"s. |
Posted By: TGerber
Date Posted: 06 May 2020 at 8:24pm
| Check out Houle Magnum manure pumps by GEA-lots in our area- good pumps from what I've heard. |
Posted By: DanWi
Date Posted: 06 May 2020 at 10:10pm
| Anybody that had a slurrystore had some kind of pump. Sand bedding and pumps are not a good combination. If I was doing something like that I would try to stay above ground when that stuff quits working maintenance is expensive. |
Posted By: JC-WI
Date Posted: 06 May 2020 at 11:29pm
|
Buckyman, there were only two that I seen in our area, Patz and Nesseth. Googled Patz... Built in Pound WI.  http://patzcorp.com/wp-content/uploads/2017/03/1512-Manure-Pump-Sell-Sheet_PA-18808-spc.pdf" rel="nofollow - http://patzcorp.com/wp-content/uploads/2017/03/1512-Manure-Pump-Sell-Sheet_PA-18808-spc.pdf to much other stuff involved... imo http://patzcorp.com/wp-content/uploads/2017/03/Tundra-LTX-Brochure-PA-30202-spec.pdf" rel="nofollow - http://patzcorp.com/wp-content/uploads/2017/03/Tundra-LTX-Brochure-PA-30202-spec.pdf http://patzcorp.com/wp-content/uploads/2017/03/Tundra-Pro-II-Brochure-PA-28907-spec.pdf" rel="nofollow - http://patzcorp.com/wp-content/uploads/2017/03/Tundra-Pro-II-Brochure-PA-28907-spec.pdf http://patzcorp.com/wp-content/uploads/2013/11/Manure-Pumps-All-1.pdf" rel="nofollow - http://patzcorp.com/wp-content/uploads/2013/11/Manure-Pumps-All-1.pdf N-Tech pumps... Built in Barron WI.  http://www.nthusa.com/pistonpump" rel="nofollow - http://www.nthusa.com/pistonpump Fellow built his pit on a sidehill back in the 1970's, short distance from the barn and used a 40 foot extended chute to run the manure out to the pit... agitated the manure for a few days and then had a gate an the low bottom corner and flowed the manure into the tanker... guess it worked pretty good, was there (and still is) until the family decided to quit milking about 6 years ago. The hydraulic unites usually are down in a pit...where bad gases can collect. Mechanicals are at ground level. Seen where a fellow moved heifers into a barn during the winter and started the system up... and 5 months later, the owner of the property had an auction and there was a sight to see, huge slabs of cement laid on top the manure piles. The end of the outlet had frozen and let the manure lift the cement up. ------------- He who says there is no evil has already deceived himself The truth is the truth, sugar coated or not. Trawler II says, "Remember that." |