Farm Equipment - Allis 190 transmission

Print Page | Close Window

Allis 190 transmission

Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=168214
Printed Date: 04 Oct 2025 at 8:10am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com

Topic: Allis 190 transmission

Posted By: Nwest
Subject: Allis 190 transmission
Date Posted: 10 Feb 2020 at 12:32pm

Hi again everyone I'm going through an allis 190 gas serial number 7995. I have the tractor split and am in need of several transmission gears. At some point in its life it took a bit of abuse being slammed into gears by the way the gears are worn. There are a couple gears that dont appear to be made anymore. The input shaft number 70245722 being one of them. Does anyone know if its possible to get these parts new? Otherwise the salvage yards I'm sure have some. Thank you

Replies:

Posted By: DrAllis
Date Posted: 10 Feb 2020 at 2:41pm

I don't think there's any of the transmission parts available for that tractor. That is the transmission that, if it was a 190XT, everything was replaced with beefier parts, including the shafts. They didn't update any straight 190's, as they didn't feel there would be any problem due to less HP. I'm afraid all you can hope for is used parts from a salvage yard. Be sure they understand it is a 190 tractor PRIOR TO S/N 9001. Any 190XT has different parts and any 190 after s/n 9001 has the same parts as the XT's.

Posted By: Nwest
Date Posted: 10 Feb 2020 at 8:16pm

Thanks for the input Dr. Allis. On that note if anyone on this forum has a few early 190 gears I'd be interested or I may be forced to scrap if I have no luck at the yards.

Posted By: MACK
Date Posted: 10 Feb 2020 at 8:55pm

I have a later rear end assembly from a 190XT gas, I would make a trade with you.
. MACK

Posted By: JC-WI
Date Posted: 11 Feb 2020 at 12:04am

Just wondering if any gears from a D19 would fit up in there...

-------------
He who says there is no evil has already deceived himself
The truth is the truth, sugar coated or not. Trawler II says, "Remember that."

Posted By: DrAllis
Date Posted: 11 Feb 2020 at 7:12am

Nope.

Posted By: lowell66dart
Date Posted: 11 Feb 2020 at 10:01am

PM sent

-------------
AC 6080 (8030,7060,200,175,D-17HC, 6040,160,6140 all gone) Farmall 1066 & 656 Hi-Clear (for sale), White 2-62 High Clearance, JD 4255 Hi Clear.

Posted By: Leon B MO
Date Posted: 11 Feb 2020 at 5:28pm

would the complete trans/rear end of a D-19 bolt up to the early 190 torque tube?

Leon B MO

-------------
Uncle always said "Fill the back of the shovel and the front will take care of itself".

Posted By: Acdiesel
Date Posted: 11 Feb 2020 at 7:15pm

did you check with this Guy?

C.L. ad

link: https://mankato.craigslist.org/grd/d/sleepy-eye-allis-chalmers-tractors/7046074966.html" rel="nofollow - allis chalmers tractors

-------------
D19 Diesel,D17 Diesel SER.3
2-D14, 2-D15 SER.II WF/NF
D15 SER.2 DIESEL
D12 SER.I, D10 Ser.II
2-720'S D21 Ser. II

Gmc,caterpillar
I'm a pharmacist (farm assist) with a PHD (post hole digger)

Posted By: MACK
Date Posted: 11 Feb 2020 at 9:30pm

Housing will bolt up, but input shaft is different.
. MACK