1952 Model D Grader
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Construction and other equipment
Forum Description: everything else with orange (or yellow) paint
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=156573
Printed Date: 04 May 2024 at 5:28pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 1952 Model D Grader
Posted By: Wild Bill 2 u
Subject: 1952 Model D Grader
Date Posted: 21 Dec 2018 at 9:24am
|
Anyone have parts for one of these?
If anyone wants or needs a propane conversion for a D get back at me, I have one I will trade or sell...........It can be found here https://1952acmodeld.tumblr.com" rel="nofollow - https://1952acmodeld.tumblr.com Thanks
|
Replies:
Posted By: DiyDave
Date Posted: 21 Dec 2018 at 8:46pm
| You're at the right place, welcome to the forum. What parts do you need? |
Posted By: Wild Bill 2 u
Date Posted: 21 Dec 2018 at 9:18pm
| I am looking for either specs (working dimensions so I can fab one) on a scarifier, or a scarifier. I need also need the ram that goes with it as well. Thanks Bill |
Posted By: Wild Bill 2 u
Date Posted: 26 Dec 2018 at 10:52pm
| I am also looking for soft cab parts? |
Posted By: wn willis
Date Posted: 29 Jan 2019 at 2:10pm
D grader 1952 Ser # D 1547. Has a Zenith Carb I have not been able to identify. Numbers on small round tag as follows: 22825, directly opposite, 115?8. The question mark is because I cannot determine the number. It appea rs to be a 6 but not sure. |
Posted By: DiyDave
Date Posted: 29 Jan 2019 at 6:33pm
Carb should be same as wd/wd 45 ag tractor uses. I have the scarifier, on mine, but its too damn cold right now to measure it up for you. You might wanna get yourself a manual, for it, I know Jensales sells 'em, they are a poor excuse for a manual (poor copy re-print), but easy to find there. Once you have a manual, its easy to see the measurements you will need. Its not a full width scarifier, basically about 3-3/12" wide, 6-7 shanks, suitable for ripping up the center weedy section of a 2 track road...
|
Posted By: Jim.ME
Date Posted: 29 Jan 2019 at 7:18pm
|
The 8 in the 22825 doesn't look quite the same as the 8 in the other number. Could the number be a 6? Could the number you can't make out be an 8? 226257 would match to a Zenith carb with a production number of 11588, used on AC's, according to a list on Norfar's industrial carb website. |
Posted By: wn willis
Date Posted: 30 Jan 2019 at 9:40am
|
You have solved my problem in identifying the carb. Much appreciated. |
Posted By: wn willis
Date Posted: 30 Jan 2019 at 1:30pm
|
Finally uncovered the moter ser#. 45-55237-G |
Posted By: wn willis
Date Posted: 30 Jan 2019 at 1:32pm
|
Now to identify correct carburetorfor that motor. |
Posted By: CAL(KS)
Date Posted: 30 Jan 2019 at 3:34pm
|
Tsx 464 should be a correct Marvel Schebler carb for that motor. dont know on the zenith ------------- Me -C,U,UC,WC,WD45,190XT,TL-12,145T,HD6G,HD16,HD20 Dad- WD, D17D, D19D, RT100A, 7020, 7080,7580, 2-8550's, 2-S77, HD15 |
Posted By: wn willis
Date Posted: 30 Jan 2019 at 3:56pm
|
That sounds good. Thank uou. |
Posted By: ac fleet
Date Posted: 17 Feb 2019 at 7:10pm
|
My 51 D only has the ram and valve/hoses. no scar. on it. would also like to make one. thanks; ac fleet P.S. Tumblr has lost it! LOL!!! they did the same to me over there! Don't know why they turned into such asses! ------------- http://machinebuildersnetwork.com/ |