1976 720 - Red Wire Caught fire ?
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Garden Tractors
Forum Description: A great place to discuss the Simplicity and Allis Chalmers Garden Models
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=152845
Printed Date: 27 Dec 2024 at 1:28am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 1976 720 - Red Wire Caught fire ?
Posted By: rhunt12312
Subject: 1976 720 - Red Wire Caught fire ?
Date Posted: 08 Aug 2018 at 4:59pm
|
Hello all
Recently picked up my late grandfathers 720S that he dearly loved and I am proud to keep in the family and working.
Runs well cut grass 2x and on the 3rd time cutting engine quite and then a red wire that was connected to just the right side of the medal frame near the snow thrower PTO caught fire and broke off. I checked gas amount and after a few minutes it started and I put back in the garage.
Gas cap may need replacing as I investigate the venting issue last night but wonder what that wire is and why it burnt up. It goes and connects to a electronic board up near the inside ignition switch.
14 HP Kohler Engine
|
Replies:
Posted By: AC720Man
Date Posted: 08 Aug 2018 at 9:09pm
Hot wire must have rubbed the frame and grounded out. That’s my guess. Frame will be black from the spark where it made contact.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: AC720Man
Date Posted: 08 Aug 2018 at 9:12pm
Would have to see a wiring diagram to see what it goes to.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: rhunt12312
Date Posted: 09 Aug 2018 at 8:27am
|
Thanks for comments guys. Wire looks like it was attached to frame with black tape. Anyone know where I could find the wiring diagram? I have original Owners Manual but not in there.
|
Posted By: AC720Man
Date Posted: 09 Aug 2018 at 11:08am
Must not be the 720 that I have, it's has the Onan 19.5 hp engine. I could have helped ya if it was.
-------------
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
Posted By: rhunt12312
Date Posted: 12 Aug 2018 at 11:26am
|
OK my bad bigtime. It is a 712H not the 720. I think the wire was ground wire. replaced it and secured to frame as a ground. Started, ran for few secounds and cut off with the smell of burning electrical. Now will not even produce any sound of trying to start. What did I blow and how to diagnose? Also a wire diagram showing where it goes to the tractor would be nice. Anyone know were to download?
|
Posted By: Steve in NJ
Date Posted: 23 Aug 2018 at 6:24am
|
I'm surprised you can't find a wiring diagram on the internet. The wiring in a 716H is basically the same wiring if you don't find a 712H diagram. I'll havta' look in my wiring diagrams at the shop. I can to tell you what the red wire is and where it goes. I offer a harness for the 700 series GT's. If it was a 720, the red wire in the engine area is the oil pressure circuit on the Onan engine... mailto:Steve@B&B" rel="nofollow - Steve@B&B
-------------
39'RC, 43'WC, 48'B, 49'G, 50'WF, 65 Big 10, 67'B-110, 75'716H, 2-620's, & a Motorhead wife
|
|