steering wheel shaft
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=145135
Printed Date: 22 Aug 2025 at 5:40pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: steering wheel shaft
Posted By: Ted in NE-OH
Subject: steering wheel shaft
Date Posted: 05 Dec 2017 at 6:54pm
|
I need to make a new steering wheel shaft so I meed to know the over all length from tip to tip. The shaft needs to be out of the housing. Note this is a Ross steering box. ------------- CA, WD, C, 3 Bs, 2 Gs, WC, I-400, 914 |
Replies:
Posted By: theropod
Date Posted: 05 Dec 2017 at 6:58pm
For what tractor? ------------- Put the bunny back in the box! 1938 B, 1977 Yanmar YM2200 No private messages: use email: theropod AT yahoo DOT com |
Ted in NE-OH wrote:Posted By: Dakota Dave
Date Posted: 05 Dec 2017 at 7:26pm
| You know that the worms gear is part of the shaft and not a seperate piece. The length of the shaft varies with the tractor serial number. It either 46 5/8" 46 7/8" or 47" unless it's a IB than its 31 5/8". |
Posted By: Ted in NE-OH
Date Posted: 06 Dec 2017 at 9:42am
|
It is for a 1939 AC B Thanks ------------- CA, WD, C, 3 Bs, 2 Gs, WC, I-400, 914 |
Posted By: theropod
Date Posted: 06 Dec 2017 at 10:04am
I have a spare if it is the right gear system, and you are welcome to it if you pay shipping. I am going to rob the steering wheel off of it anyway, so it wouldn’t be too much trouble to pull the shaft. How do I figure out which box is the one for the shaft you need? My spare tractor and the one I am bring back look exactly the same to me. I will go take a picture of what I have and post it. Give me 20-30 minutes. ------------- Put the bunny back in the box! 1938 B, 1977 Yanmar YM2200 No private messages: use email: theropod AT yahoo DOT com |
Posted By: theropod
Date Posted: 06 Dec 2017 at 10:22am
OK, here are 3 views of the steering gearbox on my spare B. If this is what you need just ask and it's yours.   ------------- Put the bunny back in the box! 1938 B, 1977 Yanmar YM2200 No private messages: use email: theropod AT yahoo DOT com |
Posted By: theropod
Date Posted: 06 Dec 2017 at 7:04pm
|
OK, I have an offer for someone to buy the entire steering sector minus the steering wheel, So, Ted if you want this shaft you have 24 hours to let me know. I need to offset some of the costs of my new mag, carb, ect. Respond in this thread as private messages on my phone doesn't allow me to respond. Thanks. ------------- Put the bunny back in the box! 1938 B, 1977 Yanmar YM2200 No private messages: use email: theropod AT yahoo DOT com |
Posted By: Ted in NE-OH
Date Posted: 06 Dec 2017 at 7:20pm
|
Thanks, but I am going to get some machining experience. I need the pratice. ------------- CA, WD, C, 3 Bs, 2 Gs, WC, I-400, 914 |
Posted By: theropod
Date Posted: 06 Dec 2017 at 7:54pm
OK, have you found the info you were needing? Since I am pulling this steering sector off my parts tractor anyway I can measure it. This is another 38 and can get a serial number if that helps. ------------- Put the bunny back in the box! 1938 B, 1977 Yanmar YM2200 No private messages: use email: theropod AT yahoo DOT com |