720 Wiring to Operate Lawn Sprayer
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Garden Tractors
Forum Description: A great place to discuss the Simplicity and Allis Chalmers Garden Models
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=130086
Printed Date: 02 Oct 2024 at 11:32am
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 720 Wiring to Operate Lawn Sprayer
Posted By: Dave (NE)
Subject: 720 Wiring to Operate Lawn Sprayer
Date Posted: 16 Oct 2016 at 4:36pm
|
I want to use my 720 to operate the pump on my lawn sprayer. With the battery in the front of the tractor, has anyone run an electric line to the back of the tractor to make it easier to connect the connections from the lawn sprayer pump to? Am looking for ideas on how to best do this. Thanks, Dave
|
Replies:
Posted By: den/southern illinoi
Date Posted: 16 Oct 2016 at 5:55pm
I've done that on at least 2 of my 720s. On the left hand side of the dash there is a place for another switch. That's where we mounted the switch and then out under the seat. We used trailer wiring pigtails for the connection to the sprayer that we have. Den
-------------
Own 4 wheel 20, 2-5015, 5020 and associated equipment and 2 electric forklifts.
|
Posted By: Dave (NE)
Date Posted: 16 Oct 2016 at 6:08pm
|
So, Den, you just ran a line directly from the battery to the switch you inserted in the dash, then on to back under the seat for the connection to the sprayer, if I understand it correctly? Tkx, Dave
|
Posted By: rrhead(SD)
Date Posted: 16 Oct 2016 at 6:16pm
On my 720, there is no PTO shaft in it. I just took the wiring from the rear pto clutch switch and added on wire to the rear of the tractor. Used a two prong plug on it and the sprayer wiring. Use the switch on console to turn sprayer on and off. rrhead(SD)
-------------
2 WDs,WD45,D-14,D-17,D-19D,180,7020,6080FWA,6080 2wd, 6080 2wd(cab),8050FWA,8550,4W-305,Massey 8250. Gleaner L3, R62 &R65 Agco-Allis 1616H & 1920H, AC 720, Terra-Tiger
|
Posted By: Dave (NE)
Date Posted: 16 Oct 2016 at 6:17pm
|
I do have pto, so probably can't route it that way.
|
Posted By: den/southern illinoi
Date Posted: 16 Oct 2016 at 7:11pm
Actually when we installed the switches, we were rewiring the tractors, adding relays, fuses, etc as the original wiring was shot. I can't seem to find the picture now but it was all installed under the dash. Most likely a little overkill but I have no electrical problems anymore. So the power actually came from a newer power location under the dash. The outlet had both a relay and fuse besides the switch. Den
-------------
Own 4 wheel 20, 2-5015, 5020 and associated equipment and 2 electric forklifts.
|
Posted By: Steve in NJ
Date Posted: 19 Oct 2016 at 6:35am
Nothin' wrong with installing relays etc. especially when you have to send power a distance. Good practice to use Den! Relays are designed to stabilize power in the system to the load its suppling. This way the load gets maximum power as it should. No voltage drop, no issues.
Steve@B&B
-------------
39'RC, 43'WC, 48'B, 49'G, 50'WF, 65 Big 10, 67'B-110, 75'716H, 2-620's, & a Motorhead wife
|
Posted By: coggonobrien
Date Posted: 21 Oct 2016 at 7:46am
|
Steve, sounds like an opportunity for you to come up with a clean kit, I've been wanting to do the same thing too.
|
Posted By: Dave (NE)
Date Posted: 22 Oct 2016 at 11:48am
|
I got the wire run to the back of the tractor. Have it connected from a switch I installed in the dash. I'm going to put a fuse in the line under the dash, after the switch. What would be a good size fuse to put in it? The sprayer has a 10 amp fuse in the line before the pump, so I know I need at least a larger one than that, but should I go even larger like with a 30 amp fuse? Tkx, Dave
|
Posted By: steve(ill)
Date Posted: 22 Oct 2016 at 9:05pm
the fuse should be to protect the wire... If you ran 12 gauge wire, you can use a 20 amp fuse. If you ran 14 gauge wire you can use a 15 amp fuse. If you ran a 16 gauge wire you can use a 10 amp fuse... smaller than 16 gauge, you are in trouble.
-------------
Like them all, but love the "B"s.
|
Posted By: Dave (NE)
Date Posted: 23 Oct 2016 at 8:33am
|
ok, that's exactly what I needed to know. Looks like a 15 amp fuse it will be. tkx Steve.
|
|