Farm Equipment - Wedge Pin part numbers???

Print Page | Close Window

Wedge Pin part numbers???

Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=11437
Printed Date: 30 Jan 2025 at 11:58pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com

Topic: Wedge Pin part numbers???

Posted By: CTuckerNWIL
Subject: Wedge Pin part numbers???
Date Posted: 23 Apr 2010 at 8:37pm

Anybody know the part numbers for the G wedge pin and the CA front cultivator wedge pin? I'm just wondering if the are the same part number.

-------------
http://www.ae-ta.com" rel="nofollow - http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF

Replies:

Posted By: David Maddux
Date Posted: 24 Apr 2010 at 6:51am

Charlie: I don't know the part no.s, but Doc Smith sells reproduction G wedge pins. Dave.

Posted By: ibleedorange
Date Posted: 24 Apr 2010 at 11:36am

316356 is the part number.

-------------
Tractors; If it runs, use it. Motorcycles: Ride em like today is your last day.

Posted By: ibleedorange
Date Posted: 24 Apr 2010 at 11:38am

Sorry, 316356 is for the G.

-------------
Tractors; If it runs, use it. Motorcycles: Ride em like today is your last day.

Posted By: Bud(WI)
Date Posted: 24 Apr 2010 at 9:30pm

My cultivator book shows 316356 for the CA as well.

Posted By: CTuckerNWIL
Date Posted: 25 Apr 2010 at 7:22am

Thanks guys, I kinda thought they might be the same part number.

-------------
http://www.ae-ta.com" rel="nofollow - http://www.ae-ta.com
Lena 1935 WC12xxx, Willie 1951 CA6xx Dad bought new, 1954WD45 PS, 1960 D17 NF

Posted By: Creek Jenkins
Date Posted: 10 May 2010 at 11:54am

Anybody have dimensions for the G wedges? I'd like to make a set.

cheers,

Creek

Posted By: Dusty MI
Date Posted: 10 May 2010 at 5:42pm

I have a couple of them. I measure them and get back latter, have a meeting to go to.

Dusty

-------------
917 H, '48 G, '65 D-10 series III "Allis Express"

Posted By: Dusty MI
Date Posted: 10 May 2010 at 9:58pm

The wedge pins are 6" long, 3/8" thick, 1 1/4" wide at the top, and 9/16" at the bottom. They are not a straight tapper, they are 1" wide in the middle/center. The sides have a slight arch to them. And the edges have a radis of about 7/16" dia. which fits into the arch in the end of the slot the wedge goes into.

The wide end of the wedge pin has a 3/8" hole 1/2" from the end and centered from the sides.

Dusty

-------------
917 H, '48 G, '65 D-10 series III "Allis Express"

Posted By: Creek Jenkins
Date Posted: 11 May 2010 at 7:53am

Dusty -

Thanks a bunch, I'm going to see if I can get a pattern burned out here at work. I can do the finish grinding at home. If I remember right there is a light chain that runs to the lift arms so you don't lose them.

thanks again and cheers,

Creek