45 Pulling tractor
Printed From: Unofficial Allis
Category: Allis Chalmers
Forum Name: Farm Equipment
Forum Description: everything about Allis-Chalmers farm equipment
URL: https://www.allischalmers.com/forum/forum_posts.asp?TID=106767
Printed Date: 18 Aug 2025 at 2:05pm
Software Version: Web Wiz Forums 11.10 - http://www.webwizforums.com
Topic: 45 Pulling tractor
Posted By: Charlie175
Subject: 45 Pulling tractor
Date Posted: 27 May 2015 at 6:23am
|
What do you all think about this tractor? http://www.ebay.com/itm/1955-ALLIS-CHALMERS-SHOW-PULLING-TRACTOR-WD45-ATTENTION-TO-DETAIL-HARLEY-RARE-/321763181612?pt=LH_DefaultDomain_0&hash=item4aea94842c" rel="nofollow - http://www.ebay.com/itm/1955-ALLIS-CHALMERS-SHOW-PULLING-TRACTOR-WD45-ATTENTION-TO-DETAIL-HARLEY-RARE-/321763181612?pt=LH_DefaultDomain_0&hash=item4aea94842c  ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Replies:
Posted By: Charlie175
Date Posted: 27 May 2015 at 6:24am
|
What motor is in it? 3 carb setup must be fun to sync. ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Posted By: BPM75
Date Posted: 27 May 2015 at 6:40am
|
I'm not sure what motor it is, but wow they done a nice job on that tractor, very clean and well built. ------------- 59 D17 gas nf, 66 XT 190, 69 220. |
Posted By: Charlie175
Date Posted: 27 May 2015 at 6:46am
|
That intake/header exhaust is a mint! Is it a 292 motor? ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Posted By: BennyLumpkin
Date Posted: 27 May 2015 at 8:44am
|
If I remember it's a modified 302 GMC ------------- Central PA Allis Express 1934 WC254 1945 WF 1945 WC135755 1951 WD68085 1953 WD45-150217 1957 WD45D-230744D B110 |
Posted By: VFDfireman
Date Posted: 27 May 2015 at 9:01am
|
Is the handle on the right fender the throttle? Not familiar with pulling tractors... |
Posted By: Charlie175
Date Posted: 27 May 2015 at 9:11am
|
Yes the throttle is on the right fender. It's called a deadman as it is spring tensioned so that if you let go it pulls back so that the tractor does not "run away" Man that header is a thing of beauty!  ------------- Charlie '48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD |
Posted By: HudCo
Date Posted: 27 May 2015 at 9:11am
| im sure somone on here will know whos it is does look sharp |
Posted By: BPM75
Date Posted: 27 May 2015 at 9:23am
|
Description says engine is a 1952 525 cid ------------- 59 D17 gas nf, 66 XT 190, 69 220. |
Posted By: acd21man
Date Posted: 27 May 2015 at 11:47am
|
wounder how many plows it can pull lol . ------------- 2 wd 45,2 D-17 diesel/gas 3 pt, 220,d21, 4020,2 4430s used daily http://www.youtube.com/channel/UCudh8Xz9_rZHhUC3YNozupw |
Posted By: 427435
Date Posted: 27 May 2015 at 9:33pm
|
What class would that pull in?? Most non-turbo classes have an rpm limit and stock block rules. I don't know what stock WD45 block could be opened up to 500+ cu. in. ------------- Mark B10 Allis, 917 Allis, 7116 Simplicity, 7790 Simplicity Diesel, GTH-L Simplicity Ignorance is curable-----stupidity is not. |
Posted By: Brian-KS
Date Posted: 27 May 2015 at 9:59pm
Looks Good 
------------- EAT BEEF! |
Posted By: acd21man
Date Posted: 27 May 2015 at 10:26pm
|
wait it cant be a gmc 302 the ex and air intank is in the other side of the block right?? ------------- 2 wd 45,2 D-17 diesel/gas 3 pt, 220,d21, 4020,2 4430s used daily http://www.youtube.com/channel/UCudh8Xz9_rZHhUC3YNozupw |
Posted By: DaveKamp
Date Posted: 27 May 2015 at 10:53pm
|
Well... unless they mounted the engine backwards... and they could have... ------------- Ten Amendments, Ten Commandments, and one Golden Rule solve most every problem. Citrus hand-cleaner with Pumice does the rest. |
Posted By: acd21man
Date Posted: 27 May 2015 at 10:55pm
|
water pump is still in the front. and timing cover iv been lookin for about a hour know lol i give up im going to bed ha ------------- 2 wd 45,2 D-17 diesel/gas 3 pt, 220,d21, 4020,2 4430s used daily http://www.youtube.com/channel/UCudh8Xz9_rZHhUC3YNozupw |
Posted By: DaveKamp
Date Posted: 27 May 2015 at 11:19pm
|
Perhaps and RD-501... with a taller valve cover?... nahh... lower block has curves around each cylinder. Hmmm... ------------- Ten Amendments, Ten Commandments, and one Golden Rule solve most every problem. Citrus hand-cleaner with Pumice does the rest. |
Posted By: BennyLumpkin
Date Posted: 27 May 2015 at 11:21pm
|
I didn't even pay attention to which side they were...thought I had read it awhile back ------------- Central PA Allis Express 1934 WC254 1945 WF 1945 WC135755 1951 WD68085 1953 WD45-150217 1957 WD45D-230744D B110 |
Posted By: acd21man
Date Posted: 30 May 2015 at 8:06pm
|
7700 and a few mins left any1 guna bid on it lol ------------- 2 wd 45,2 D-17 diesel/gas 3 pt, 220,d21, 4020,2 4430s used daily http://www.youtube.com/channel/UCudh8Xz9_rZHhUC3YNozupw |
Posted By: acd21man
Date Posted: 30 May 2015 at 8:26pm
|
figured it out its a 503 gmc. i was wrong:(. didnt no they made them. look them up ------------- 2 wd 45,2 D-17 diesel/gas 3 pt, 220,d21, 4020,2 4430s used daily http://www.youtube.com/channel/UCudh8Xz9_rZHhUC3YNozupw |
Posted By: thendrix
Date Posted: 30 May 2015 at 9:16pm
|
That's a slick tractor. Didn't sell at 9200 ------------- "Farming is a business that makes a Las Vegas craps table look like a regular paycheck" Ronald Reagan |
Posted By: Brian-KS
Date Posted: 30 May 2015 at 9:50pm
|
I contacted him about the engine. This is what he wrote back: 1952 gmc 800 class firetruck factory 503 ci, now 525 ci, stock stroke. ------------- EAT BEEF! |
Posted By: 427435
Date Posted: 30 May 2015 at 10:49pm
|
Again, I wonder where you would find a class that you could pull that in (other than the mod classes where that engine wouldn't be competitive). ------------- Mark B10 Allis, 917 Allis, 7116 Simplicity, 7790 Simplicity Diesel, GTH-L Simplicity Ignorance is curable-----stupidity is not. |
Posted By: SHAMELESS
Date Posted: 30 May 2015 at 11:11pm
| I have a GM 235 CID in mine, but haven't run it yets! |