This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Solar Charger on the Dozer: |
Post Reply |
Author | |
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2053 |
Post Options
Thanks(0)
Posted: 04 Nov 2024 at 8:55am |
I installed a 24VDC, 50W solar charger onto my dozer last week and really like it. Since the onset of stage IV CRS disease got hold of my dumbazz, I can't remember to shut the master disconnect off and consistently have to boost the tractor to start it. Anyways, I got one of these things, set it up at 4:00pm one afternoon on the two series wired 4D batteries depleted severely to allow a test scenario. 40 hours later I opened the battery compartment and the little annunciator on the charge controller showed the batteries fully charged. Mashing the start button the engine rolled right over easily, (as usual). I then did a couple of extended crank cycles with the fuel shut off to draw off the surface charge and then let the batteries deplete again to 9.6VDC each. Reconnecting the solar charger, I monitored again this time at 30hrs and they were still charging in bright sunlight. At 40hrs they were fully charged again, and the engine fired easily. I have a 1000A carbon pile battery tester on order but have not yet received it. I will give the batteries a good workout once that arrives but if I can remember to turn the disconnect off, they don't have problems retaining charge level. They were both new in July 2021. Here is the one I purchased: https://www.amazon.com/gp/product/B0C811GT61/ref=ox_sc_act_title_1?smid=A3QZRVGKEACR7A&th=1 I'm going to order a couple of the variants in 12VDC also as they seem to be good quality.
Edited by Codger - 04 Nov 2024 at 5:54pm |
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Sponsored Links | |
tadams(OH)
Orange Level Access Joined: 17 Sep 2009 Location: Jeromesville, O Points: 10119 |
Post Options
Thanks(0)
|
I have 3 12 volt on top of my 100 foot long building and use them especiallly in the winter just move them around to different tractors when ever I go up there and the batteries are always chargerd.
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2053 |
Post Options
Thanks(0)
|
My shop is 70X100 and is a steel frame, steel shell industrial building. I had it designed to fully cover the roof in solar panels and may yet do that. Not for charging/maintaining batteries, but rather selling generated power back to the utility provider. I keep everything on battery maintainers but the dozer shed doesn't have electrical to it so really like this panel. The mowing tractor, and chore tractor are also kept there so the combination of the three chargers would make things a lot easier overall.
|
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
PaulB
Orange Level Joined: 12 Sep 2009 Location: Rocky Ridge Md Points: 4727 |
Post Options
Thanks(0)
|
How about adding a big red light on the dash somewhere to let you know when the battery cut off switch is on?
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits. If you can't make it GO... make it SHINY |
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2053 |
Post Options
Thanks(0)
|
I did purchase an assortment of 16mm red, and green LED indicator lamps to replace the burned out incandescent originals there. On the same order also some clear bulbs to illuminate the gauge quadrant.
Also ordered the 50W, 12V variant from the same vendor as the quality is better than many I've seen. Edited by Codger - Yesterday at 5:46pm |
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |