B210 coil

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Hey all first time poster! I have a b210 and been having issues getting spark. 
so far I replaced the points condensor and coil but still can't seem to get it to spark. The coil was a stens 460-006 but I'm worried I may have purchased the wrong one or something. 

I believe I have the timing right the magnet on flywheel lines up with coil when the breaker opens but I could be doing something wrong.

 Got the tractor for 50 bucks at an auction and when you jump the starter she turns over but still can't get spark. I'd love to save this tractor but my knowledge of older equipment is limited. 

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Tmr17563 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 11 Sep 2024 Location: Lancaster pa Points: 8	Post Options Post Reply Quote Tmr17563 Report Post Thanks(0) Quote Reply Topic: B210 coil Posted: 11 Sep 2024 at 10:31am
	Hey all first time poster! I have a b210 and been having issues getting spark. so far I replaced the points condensor and coil but still can't seem to get it to spark. The coil was a stens 460-006 but I'm worried I may have purchased the wrong one or something. I believe I have the timing right the magnet on flywheel lines up with coil when the breaker opens but I could be doing something wrong. Got the tractor for 50 bucks at an auction and when you jump the starter she turns over but still can't get spark. I'd love to save this tractor but my knowledge of older equipment is limited.

Sponsored Links

acken Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 02 Jan 2014 Location: Minnesota Points: 84	Post Options Post Reply Quote acken Report Post Thanks(0) Quote Reply Posted: 11 Sep 2024 at 9:08pm
	That ignition system is grounded to shut it off. Any bare spot between the junction down at the points cover can kill your spark. When you replaced coil did you make sure small wire from coil going out to points had not rubbed through insulation? A good way to start is remove the wire going up to key switch, that will take that wire, and the switch out of the equation. If it happens to start you will need to ground out the spark plug, or ground from the connection at point cover.

Tmr17563 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 11 Sep 2024 Location: Lancaster pa Points: 8	Post Options Post Reply Quote Tmr17563 Report Post Thanks(0) Quote Reply Posted: 12 Sep 2024 at 3:34am
	I'll check it this morning the coil had 2 small wires that were bolted to where the coil mounts and the longer black wire that goes to the points so I'll go through it. The two smaller wires can they bith be grounded at the same spot or do they have to be separate?

Tmr17563 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 11 Sep 2024 Location: Lancaster pa Points: 8	Post Options Post Reply Quote Tmr17563 Report Post Thanks(0) Quote Reply Posted: 12 Sep 2024 at 3:41am
	That's the coil I bought for it the smaller wire was on one of the bolts for coil black wire I assume goes to points?

acken Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 02 Jan 2014 Location: Minnesota Points: 84	Post Options Post Reply Quote acken Report Post Thanks(0) Quote Reply Posted: 12 Sep 2024 at 9:07pm
	The small wire with the black insulation would go to the insulate stud above and to the left of the actual coil. Verify that stud still has the insulation to keep it from being grounded. I will try to get a pic showing an original in place. Is that the original engine, not a replacement that could be newer with electronic ignition (has actual breaker points/condenser)?

Tmr17563 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 11 Sep 2024 Location: Lancaster pa Points: 8	Post Options Post Reply Quote Tmr17563 Report Post Thanks(0) Quote Reply Posted: 13 Sep 2024 at 12:57am
	The stud looked like it had other wires connected to it I figured it was a ground so I extended the wire and ran it right to where the points breaker goes there's a stud inside where the condensor wire is I figured they had to be connected (totally new to the older engines) as far as I can tell this is original to the tractor

Tmr17563 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 11 Sep 2024 Location: Lancaster pa Points: 8	Post Options Post Reply Quote Tmr17563 Report Post Thanks(0) Quote Reply Posted: 13 Sep 2024 at 4:21am
	Here's how I have it set up Going to check timing of the points breaker opening up in reference to coil and magnet on flywheel I do have a old manual for setting up the timing so that should help me there.as long as my wiring setup is correct

acken Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 02 Jan 2014 Location: Minnesota Points: 84	Post Options Post Reply Quote acken Report Post Thanks(0) Quote Reply Posted: 13 Sep 2024 at 8:07pm
	Assuming that blue wire in picture goes all the way to the insulated coil wire, you will not have a way to shut it off. If you want to leave it that way for testing its fine. Eventually you will want to hook blue wire to the screw on the insulated tab outside of the point cover (in order to complete circuit to ground when you turn key off). The air gap between coil and magnets in flywheel should set at .012". Best way is if you have 2 of the correct size feeler gauges, on under each leg of coil. Line coil up with magnets, then tighten screws.

Tmr17563 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 11 Sep 2024 Location: Lancaster pa Points: 8	Post Options Post Reply Quote Tmr17563 Report Post Thanks(0) Quote Reply Posted: 14 Sep 2024 at 7:01am
	Okay I used a business card to set the coil and for now for testing I'll leave the blue wire hooked direct. Would a bad starter solenoid cause no spark? The one I have now is definitely bad I was jumping the positive wire to get it to spin over to test for spark before I threw any more parts at it.

acken Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 02 Jan 2014 Location: Minnesota Points: 84	Post Options Post Reply Quote acken Report Post Thanks(0) Quote Reply Posted: 14 Sep 2024 at 8:24pm
	Starter has no effect on spark, unless it is spinning very slow.

Tmr17563 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 11 Sep 2024 Location: Lancaster pa Points: 8	Post Options Post Reply Quote Tmr17563 Report Post Thanks(0) Quote Reply Posted: Yesterday at 10:26am
	When the engone is at top dead center and points starting to open looks like the magnet on flywheel isn't in line with the coil. I'm going to try to adjust that and go from there.