| Author |
 Topic Search  Topic Options
|
AllisFreak MN 
Orange Level Access
Joined: 07 Dec 2009
Location: Minnesota
Points: 1589
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: WD pushrod cover
Posted: 18 Jan 2023 at 7:05pm |
|
I am replacing the dried up cork gasket on the pushrod cover on the ol' WD. Any tips as far as using permatex or should I just put it on without any?
|
|
'49 A-C WD, '51 A-C WD, '63 A-C D17 Series III, 1968 A-C One-Seventy, '82 A-C 6060, '75 A-C 7040, A-C #3 sickle mower, 2 A-C 701 wagons, '78 Gleaner M2
|
 |
|
Sponsored Links
|
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Jan 2023 at 8:20pm |
|
Glue it to cover with 3M1099 glue or that yellow weather stripping glue. Let it set over night with weight on it to keep it in place. Install next morning. MACK
|
|
Les Kerf
Orange Level
Joined: 08 May 2020
Location: Idaho
Points: 1364
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Jan 2023 at 8:46pm |
|
I've been messing with this stuff for 50+ years now; my Dad always used Permatex Aviation #2 gasket sealer. It is messy, sticky, gets on your fingers, in your hair and is miserable to scrape off the next time.
But it works.
When I got out on my own I read about folks saying that a properly prepared gasket surface didn't need goop to seal, so I tried and failed. I tried silicones and I tried various things with varied results.
When I really, truly don't want to mess with it for a long time I still go back to Permatex aviation gasket sealer.
Your mileage may vary.
Good luck :-)
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8671
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Jan 2023 at 11:07pm |
|
I use MACK's method successfully
|
|
Dirt Farmer
Silver Level Access
Joined: 15 Sep 2020
Location: Illinois
Points: 446
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jan 2023 at 1:20am |
|
Im in agreement with Mack and Steve. Around here we refer to it as gorilla snot
|
|
Eric B
Orange Level
Joined: 09 Feb 2012
Location: British Columbi
Points: 978
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jan 2023 at 12:19pm |
|
X2 for Les Kerf. I know different methods and sealers will bring results but in my opinion Permatex Aviation is at the top of the success list. Silicone Ultra Grey will really resist oil leaks. Using Permatex Aviation on both sides makes an awesome seal but the gasket is rarely reusable if you remove the part again in the future.
|
|
Currently- WD,WC,3WF's,2 D14's B. Previously- I 600,TL745,200,FL9,FR12,H3,816 LBH. Earth has no sorrow that Heaven cannot heal!
|
|
LaJaMe
Bronze Level
Joined: 14 Sep 2014
Location: wisconsin
Points: 172
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jan 2023 at 11:07pm |
|
When my Dad was a dealer, he would shelack the gasket to the cover and then grease the block side. This was so he could get the cover back off if valves needed readjusting. He never had a problem!!!!
|
|
Bill_MN
Orange Level
Joined: 12 Sep 2009
Location: Sioux Falls, SD
Points: 1471
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 Feb 2023 at 6:56pm |
|
Indian Head Gasket shellac is my go-to on cork gaskets.
|
|
1951 WD #78283, 1918 Case 28x50 Thresher #76738, Case Centennial B 2x16 Plow
|
|
Michael V (NM)
Orange Level Access
Joined: 12 Sep 2009
Location: NM
Points: 2486
|
Post Options
Thanks(0)
Quote Reply
Posted: 01 Feb 2023 at 8:01pm |
if ya do like Mack says,, that gasket will defiantly stay on the piece its glued to. I like the permatex aviation or whatever is similar, it stays kinda soft and seems to seal decent,,,
|
|
AllisFreak MN
Orange Level Access
Joined: 07 Dec 2009
Location: Minnesota
Points: 1589
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Feb 2023 at 8:06pm |
|
Yup I did as Mack said and it worked great. Man was there a lot of old sludge behind that cover and the old cork gasket was rock hard and brittle.
|
|
'49 A-C WD, '51 A-C WD, '63 A-C D17 Series III, 1968 A-C One-Seventy, '82 A-C 6060, '75 A-C 7040, A-C #3 sickle mower, 2 A-C 701 wagons, '78 Gleaner M2
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 22133
|
Post Options
Thanks(0)
Quote Reply
Posted: 02 Feb 2023 at 8:26pm |
|
I think that is why they had that cover removeable was to be able to clean the engine due to non-detergent oils.
|
|
