| Author |
 Topic Search  Topic Options
|
DARRELL(PEI) 
Silver Level
Joined: 11 Sep 2009
Location: Canada, PEI
Points: 50
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 670t
Posted: 09 Mar 2012 at 9:43am |
|
Located this motor, out of a 7045 and would like to know the good and bad of It, and will It fit Into a 220.Still looking for a good motor for the 220 and hope this works out, not much to choose from when dealing here on the Island. Thanks for any help on this.
|
 |
|
Sponsored Links
|
|
|
Jordan(OH)
Orange Level
Joined: 11 Sep 2009
Location: Celina, OH
Points: 1563
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2012 at 10:15am |
|
Direct bolt in, no. Will it work, yes. Do you have the original 220 engine?
|
|
Calvin Schmidt
Orange Level
Joined: 11 Sep 2009
Location: Ontario Can.
Points: 4540
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2012 at 11:52am |
We're installing a 3500 MK II (same as 670T) in a 220 now. You will need to change the bottom rad inlet to the left side. Not sure about the front plate. My engine was a power
|
|
Nothing is impossible if it is properly financed
|
|
Calvin Schmidt
Orange Level
Joined: 11 Sep 2009
Location: Ontario Can.
Points: 4540
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2012 at 11:54am |
One  ong picture above. Left side
|
|
Nothing is impossible if it is properly financed
|
|
DARRELL(PEI)
Silver Level
Joined: 11 Sep 2009
Location: Canada, PEI
Points: 50
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2012 at 12:45pm |
|
so your saying the MK 11 3500 would be a much better fit, less time In fitting It In. I had a lead on a Mk11 In New Brunswick which Is on a gen set, so I am going In that direction until I hear other wise. Thanks Guys.
|
|
TexasAllis
Silver Level
Joined: 14 Sep 2009
Location: Texas
Points: 396
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2012 at 12:52pm |
 Calvin Schmidt wrote:
One long picture above. Left side |
So when you put a power plant in a tractor do you have to change the pump settings?
|
|
1944 Allis C
1960 Allis D-17 LP
|
|
Calvin Schmidt
Orange Level
Joined: 11 Sep 2009
Location: Ontario Can.
Points: 4540
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2012 at 1:20pm |
 My engine was on a water pump and had 82 original hours. The book said it was an 'on highway' engine. It has a variable speed govenor so we're good to go. Luckily the front plate had the mounting for a compressor which is the same as a hydraulic pump. If the engine is from a combine it will not have that opening. Front plates vary depending on application. Since this engine already had the hydraulic pump mount, it was simple to change the mounts to the tractor frame. A 670T may not mount any different that a 3500 MK II. It all depends on it previous application. The good part about the Mk II and 670 engines is the piston cooling. We added the intercooler. I just looked at some pictures of a 7030 that I'm picking up tomorrow and noticed that the front plate does not have the hydraulic pump mounts that you need. This will be the same on a 7045. I have a bad engine that could yield a front plate if you can't find one that loose somewhere.
Edited by Calvin Schmidt - 09 Mar 2012 at 1:28pm
|
|
Nothing is impossible if it is properly financed
|
|
Pete from IL
Silver Level
Joined: 29 Dec 2009
Location: Beecher IL.
Points: 311
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2012 at 7:49pm |
|
Calvin, I have not seen a 3500 or a 670T engine with an inline injection pump like yours. Was that in a combine?
|
|
Calvin Schmidt
Orange Level
Joined: 11 Sep 2009
Location: Ontario Can.
Points: 4540
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2012 at 10:23pm |
|
Pete, The engine discription is above. I was told that the 3500 MK II engine in big loaders also had an inline pump.
|
|
Nothing is impossible if it is properly financed
|
|
