This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


need help ca
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
acwdwcman View Drop Down
Orange Level
Orange Level
Avatar

Joined: 16 Oct 2010
Location: palmyra, il
Points: 1075 		Post Options Post Options   Thanks (0) Thanks(0)   Quote acwdwcman Quote  Post ReplyReply Direct Link To This Post Topic: need help ca
    Posted: 26 Jan 2012 at 12:50pm
 how do i take of the barrings on the front end of a narrow front ca?
wd with a freeman model 90 trip loader, wd45, 38 unstylled wc, b 10 garden tractor and 2-14 ac trip plow. grandpa has a 56 wd45. wd. allis chalmers snap coupler blade and 3 bottom snap coupler plow
Back to Top
Sponsored Links


Back to Top
JeffMOnt View Drop Down
Silver Level
Silver Level


Joined: 11 Sep 2009
Location: Ottawa, Ont
Points: 129 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JeffMOnt Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2012 at 3:16pm
From the manual:
To disassemble pedestal and front steering gear, support tractor under torque tube and remove front wheels. Remove cap screws retaining pedestal to front support and remove pedestal. Remove cap screw, washer and shims from top of vertical spindle shaft and pull pinion gear off shaft. Withdraw shaft, bearing cone and oil seal from bottom of housing. 
Back to Top
GregLawlerMinn View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Lawler, Mn
Points: 1226 		Post Options Post Options   Thanks (0) Thanks(0)   Quote GregLawlerMinn Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2012 at 3:19pm
If you mean the wheel bearings: Pull off the wheels and hubs. the bearings are ball bearings. The inside of the bearings are a tight fit to the spindles and the outside of the bearings run in a race that is pressed into the hub. You may need a puller or a chisel and BFH to take the bearings off the spindles; a chisel and hammer works well to remove the races pressed into the hubs.

Edited by GregLawlerMinn - 26 Jan 2012 at 3:20pm
What this country needs is more unemployed politicians-and lawyers.
Currently have: 1 D14 and a D15S2.
With new owners: 2Bs,9CAs,1WD,2 D12s,5D14s,3D15S2s, 2D17SIVs,D17D,1D19D;1 Unstyled WC
Back to Top
Josh Day View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Nov 2010
Location: Indiana
Points: 3427 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Josh Day Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jan 2012 at 5:25pm
Did you get a CA ?
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.074 seconds.


Help Support the
Unofficial Allis Forum