| Author |
 Topic Search  Topic Options
|
55allis 
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 938
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Restored d17 project
Posted: 17 Aug 2025 at 7:45am |
Blessed Sunday morning Just got this d17 in that does not turn over at all and I’m guessing that it’s the crank seals are the culprit due to that being the last thing that was done to it. It has been fully redone inside out supposedly. I thought that I’d post on here from the start to finish so that it’s on the record. Btw the rear crank seal is still leaking….. 
Edited by 55allis - 20 hours 21 minutes ago at 5:55pm
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21818
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 Aug 2025 at 7:57am |
|
That's a bad deal. I figured he'd have someone else (competent) fix it right and keep it after all the $$$$$ spent on it.
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 938
|
Post Options
Thanks(0)
Quote Reply
Posted: 20 hours 15 minutes ago at 6:01pm |
Update: found that all 8 push rods are bent and I call shot… The rear crank seal leak ended up being the gasket had fell into the oil pan.    Anything else I should check? I’m going to re-torque everything just to be safe. What are the common problems that cause pushrod bending? Don’t want it to do it again…
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
plummerscarin
Orange Level Access
Joined: 22 Jun 2015
Location: ia
Points: 3901
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 hours 53 minutes ago at 6:23pm |
|
In my case, the valves hung up in the head. Bent pushrods, bent valves, and left a mark in the piston where they made contact. Might even consider having the rods inspected as well.
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 938
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 hours 44 minutes ago at 6:32pm |
|
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 87563
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 hours 26 minutes ago at 6:50pm |
|
hard to believe that EVERY VALVE was stuck.. but possible... I would check the CAM TIMING... that would effect ALL valves hitting the pistons.... checking the rods for any BEND would be a good idea.
|
|
Like them all, but love the "B"s.
|
|
Les Kerf
Orange Level
Joined: 08 May 2020
Location: Idaho
Points: 1247
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 hours 47 minutes ago at 8:29pm |
 steve(ill) wrote:
hard to believe that EVERY VALVE was stuck.. but possible... I would check the CAM TIMING... that would effect ALL valves hitting the pistons.... checking the rods for any BEND would be a good idea. |
X2 The previous thread linked above gave no indication as to whether or not this engine ever ran at all and no clues as to what type of 'overhaul' was done. Wrong pistons? Increased stroke? Shaved head? High-lift cam? Timing gears thrown in there haphazardly?  I dunno, I wonder who does?
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 938
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 hours 19 minutes ago at 8:57pm |
|
Funny thing is I don’t see any damage to the pistons or valves…
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
Bingo8
Bronze Level
Joined: 04 May 2017
Location: Iowa
Points: 18
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 hours 14 minutes ago at 9:02pm |
|
Oh, I am keeping it. 55Allis is helping me out. It was an unfortunate situation. Unfortunately, I am not sure what I could have done differently when choosing him to restore it. He came highly recommended, has his work in magazines, and put clinics on for tractor restoration. Seemed like the right guy at the time. Hindsight is 20/20 but I am moving on with someone who hopefully can get it fixed up.
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 938
|
Post Options
Thanks(0)
Quote Reply
Posted: 16 hours 53 minutes ago at 9:23pm |
Found these numbers on on piston; AE 233  Maybe a brand and part number?
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8611
|
Post Options
Thanks(0)
Quote Reply
Posted: 15 hours 13 minutes ago at 11:03pm |
|
Bout have to be cam out of time unless they're all stuck
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 938
|
Post Options
Thanks(0)
Quote Reply
Posted: 14 hours 36 minutes ago at 11:40pm |
|
I’ll remove the timing gears cover and check it out.
Think I’m still going to have to split the tractor due to a hydraulic leak in the clutch housing.
Thanks!!
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21818
|
Post Options
Thanks(0)
Quote Reply
Posted: 7 hours 35 minutes ago at 6:41am |
|
There's something going on with that engine. It was a running engine !! That's why the rear seal was leaking...it RAN !! All 8 push rods bent on a running engine?? Makes you think the camshaft quit turning.
|
|
Les Kerf
Orange Level
Joined: 08 May 2020
Location: Idaho
Points: 1247
|
Post Options
Thanks(0)
Quote Reply
Posted: 6 hours 1 minutes ago at 8:15am |
|
Could the governor fail and send debris into the timing gears and cause the cam to lock up?
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21818
|
Post Options
Thanks(0)
Quote Reply
Posted: 5 hours 34 minutes ago at 8:42am |
|
Worn governor weights and timing gear damage are two things that go together. Maybe, just maybe, the governor weights blew apart while the engine was running AND no one was sitting on the seat to shut off the key ?? That might xplain the carnage. And as far as the man who restored this tractor goes, he might very well be the great restorer of SOME BRANDS of tractors, but certainly not a D-17 Allis-Chalmers. I can't imagine tackling multiple brands for restore projects and ever hope to be very successful at it. The nuances and quirks of each particular brand and model keeps most of us busy when repairing/rebuilding things.
|
|
Les Kerf
Orange Level
Joined: 08 May 2020
Location: Idaho
Points: 1247
|
Post Options
Thanks(0)
Quote Reply
Posted: 4 hours 55 minutes ago at 9:21am |
DrAllis wrote:
... Maybe, just maybe, the governor weights blew apart while the engine was running AND no one was sitting on the seat to shut off the key ?? .... |
...AND maybe the guy WAS sitting in the seat and reached around with a broomstick and shoved the throttle wide open on the carburetor...  
I spent 30 years in sawmill maintenance, and the single most difficult part about troubleshooting equipment problems was getting accurate, and COMPLETE information about what actually happened. What did you see? What did you hear? What was the machine doing immediately prior to the wreck? What was changed/adjusted? Etc.
|
|
55allis
Orange Level
Joined: 30 Jun 2020
Location: Griswold Iowa
Points: 938
|
Post Options
Thanks(0)
Quote Reply
Posted: 31 minutes ago at 1:45pm |
|
So now I’m even wondering if he ever had it running…
Spark plugs are new and never ran on (he claims put new ones after he ran it)
Pistons still have grease on top.
Crank pulley doesn’t have any paint/rust wore off from the belt.
|
|
1955 AC WD45 diesel with D262 repower, 1949 AC WD45
|
|
