| Author |
 Topic Search  Topic Options
|
DMiller 
Orange Level Access
Joined: 14 Sep 2009
Location: Hermann, Mo
Points: 32521
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Drawbar, 180
Posted: 25 Apr 2011 at 8:15pm |
|
Anyone here weld up and re-mill their drawbar at the outer pin hole? I am about to go this route and wondered if anyone had done it with poor results as in losing the temper in the bar? I am using the drawbar more often than the 3 point on the old 180 and the wear is damaging my pins/hitches on the drawn equipment.
|
 |
|
Sponsored Links
|
|
|
allis restorer
Silver Level
Joined: 05 Dec 2010
Location: Rib Lake, WI
Points: 184
|
Post Options
Thanks(0)
Quote Reply
Posted: 25 Apr 2011 at 8:18pm |
|
I welded one up 2 weeks ago and had it all milled, and turned out nice, a little bit of time involed, just weld it and let it cool on its own. I just used .035 Hard wire and keep filling it in. good luck Steve
|
|
Go orange or Go home!!
|
|
DMiller
Orange Level Access
Joined: 14 Sep 2009
Location: Hermann, Mo
Points: 32521
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Apr 2011 at 5:40am |
|
Thanks, I am going after mine as soon as I can get to it.
|
|
Clay
Orange Level
Joined: 11 Sep 2009
Location: Udall, Kansas
Points: 9580
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Apr 2011 at 8:30am |
|
What is the correct diameter of the pin hole?
|
|
Skyhighballoon(MO)
Orange Level
Joined: 11 Sep 2009
Location: Pilot Grove, MO
Points: 3115
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Apr 2011 at 8:50am |
|
Can you drill it out and weld a bushing in of the correct hole size then cut/mill off the excess bushing length on both sides do the drawbar is flat/smooth again? Mike
|
|
1981 Gleaner F2 Corn Plus w 13' flex
1968 Gleaner EIII w 10' & 330
1969 180 gas
1965 D17 S-IV gas
1963 D17 S-III gas
1956 WD45 gas NF PS
1956 All-Crop 66 Big Bin
303 wire baler, 716H, 712H mowers
|
|
DMiller
Orange Level Access
Joined: 14 Sep 2009
Location: Hermann, Mo
Points: 32521
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Apr 2011 at 11:05am |
|
I don't know what the original was as someone prior to me gas-axed the hole bigger (1 1/4" x 1 3/8") so I am going to weld it more closed, possibly weld overlay the tongue region as it too is worn severely and then re-mill it to correct thickness and drill/mill the draw pin hole to 1 1/16" so the pin will give some in maneuvering. I will have to get a photo of before and during then after as I finish up.
|
|
kev/ont
Orange Level
Joined: 12 Sep 2009
Location: Castleton Ont
Points: 282
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Apr 2011 at 11:12am |
|
if you put a piece of brass in the hole first you can weld it up without milling it afterwards. you'll be left with a round hole the size of the brass.
|
|
DMiller
Orange Level Access
Joined: 14 Sep 2009
Location: Hermann, Mo
Points: 32521
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Apr 2011 at 11:48am |
|
|
|
Hurst
Orange Level
Joined: 11 Sep 2009
Location: Midway, Ky
Points: 1213
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Apr 2011 at 1:20pm |
|
Looks good as new. Hopefully the welding didn't mess up any heat treating, if those drawbars are even heat treated metal.
Hurst
|
|
1979 Allis Chalmers 7000
5800 Hours
|
|
