| Author |
 Topic Search  Topic Options
|
dustinmo 
Orange Level Access
Joined: 12 Sep 2009
Location: Auxvasse, MO
Points: 2187
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: where to get a seal
Posted: 07 Mar 2011 at 8:03pm |
|
I need a front seal for a C where can I get one? I cant find them in the parts houses, Thanks, Dustin
|
 |
|
Sponsored Links
|
|
|
niel ev
Silver Level
Joined: 04 Feb 2010
Points: 189
|
Post Options
Thanks(0)
Quote Reply
Posted: 07 Mar 2011 at 9:11pm |
|
Which one do you need ? Niel
|
|
dustinmo
Orange Level Access
Joined: 12 Sep 2009
Location: Auxvasse, MO
Points: 2187
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Mar 2011 at 5:59pm |
|
the front crankshaft seal
|
|
CTuckerNWIL
Orange Level
Joined: 11 Sep 2009
Location: NW Illinois
Points: 22824
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Mar 2011 at 6:15pm |
|
Motion Industries, but you'll probably need the shaft diameter and the bore diameter that the seal goes into or the old seal for them to match up to.
Edited by CTuckerNWIL - 08 Mar 2011 at 6:16pm
|
|
|
|
dustinmo
Orange Level Access
Joined: 12 Sep 2009
Location: Auxvasse, MO
Points: 2187
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Mar 2011 at 6:27pm |
|
I have the dia's but it will need to be the 2 part seal with the felt and rubber, atleast that was what was in it or what was left of it anyway
|
|
Thad in AR.
Orange Level Access
Joined: 12 Sep 2009
Location: Arkansas
Points: 9559
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Mar 2011 at 6:36pm |
|
You might want to get a speedy sleeve also. Someone on here might remember what size. I used one on a B and a new style rubber seal and have no leaks.
|
|
CTuckerNWIL
Orange Level
Joined: 11 Sep 2009
Location: NW Illinois
Points: 22824
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Mar 2011 at 6:50pm |
|
The new rubber spring loaded seal should work fine. If there is a noticeable groove in the seal diameter, get a speedi sleeve for it. You might not need a speedi sleeve if the new seal casing is narrow enough to place it so the seal rides on a good surface.
Edited by CTuckerNWIL - 08 Mar 2011 at 6:52pm
|
|
|
|
dannyraddatz
Orange Level
Joined: 12 Sep 2009
Location: Plainfield, Ill
Points: 848
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Mar 2011 at 7:31pm |
I bought mine from AGCO and don't forget to pack the back side of the seal with grease so the spring will stay in place during installation.
|
|
Danny Raddatz
|
|
dustinmo
Orange Level Access
Joined: 12 Sep 2009
Location: Auxvasse, MO
Points: 2187
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Mar 2011 at 9:33pm |
|
I will check with agco, the ones I could get are for the 138s 149s and 160s and the outer dia is too big I already destroyed one getting mad and trying to MAKE IT FIT with a hammer
|
|
CTuckerNWIL
Orange Level
Joined: 11 Sep 2009
Location: NW Illinois
Points: 22824
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Mar 2011 at 1:00am |
|
The outside diameter is bigger than the bore it fits in. My brother would always take the CR seals to the belt sander before installing to put a bevel on the leading edge. If you don't have the proper tools, get a socket that is just a little smaller than the seal and us it as a punch. The seal MUST be kept parallel with the face while inserting.
Edited by CTuckerNWIL - 09 Mar 2011 at 1:03am
|
|
|
|
