This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Steering U Joint on a WD45
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Larry(OH) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Shreve Ohio
Points: 1577 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Larry(OH) Quote  Post ReplyReply Direct Link To This Post Topic: Steering U Joint on a WD45
    Posted: 20 Feb 2011 at 8:07am
My neighbor was asking me how to grease that u joint as he is replacing a NF with a WFE.  I always thought there was a zerk there, but it looks like the zerk is for the bushing that the lower shaft rides in.  SO, is there a way to gease or were these "factory sealed" u joints
'40 WC puller,'50 WD puller,'50 M puller '65 770 Ollie

*ALLIS EXPRESS contact*

I can explain it to you, BUT I cannot understand it for you!!
Back to Top
Sponsored Links


Back to Top
Brian G. NY View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: 12194
Points: 2244 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Brian G. NY Quote  Post ReplyReply Direct Link To This Post Posted: 20 Feb 2011 at 8:20am
I don't believe the originals were greasable.
I replaced the cross and bearing kit in mine with Precision (NAPA) #861 which is.
Back to Top
Don(MO) View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Bates City MO.
Points: 6862 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Don(MO) Quote  Post ReplyReply Direct Link To This Post Posted: 20 Feb 2011 at 8:24am
Larry if the unit is not installed yet lay the u-joint at a 46* to 90* angle and look in the center of cross for a little plug if there's a plug just install a 90* grease fitting in it but if  it does not have the plug now is a good time to change the cross out. He can just remove the u-joint and add grease in the cups too
Don
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.
Back to Top
Larry(OH) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Shreve Ohio
Points: 1577 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Larry(OH) Quote  Post ReplyReply Direct Link To This Post Posted: 21 Feb 2011 at 10:30am
thanks
'40 WC puller,'50 WD puller,'50 M puller '65 770 Ollie

*ALLIS EXPRESS contact*

I can explain it to you, BUT I cannot understand it for you!!
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.047 seconds.


Help Support the
Unofficial Allis Forum