| Author |
 Topic Search  Topic Options
|
Stanley 
Bronze Level
Joined: 16 Oct 2009
Location: PDC, WI
Points: 191
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: AC - WD45 OIl pressure
Posted: 09 Nov 2010 at 8:26pm |
|
I have a WD45 that starts w/ decent oil pressure and after it "warns up" the pressure drops below the "N" on the gauge.
What is the recommended oil type/weight and filter for this tractor. Also I've read on this site that the tube/pipe in the oil filter needs to be a certain length.
I have added a washer to the oil pressure relief valve and there is little if any improvement.
Any suggestions will be appreciated.
|
 |
|
Sponsored Links
|
|
|
Brian Jasper co. Ia
Orange Level
Joined: 11 Sep 2009
Location: Prairie City Ia
Points: 10508
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Nov 2010 at 9:10pm |
|
Good oil pressure cold that goes away warm usually means worn bearings. Time for an overhaul...
|
|
"Any man who thinks he can be happy and prosperous by letting the government take care of him better take a closer look at the American Indian." Henry Ford
|
|
Stanley
Bronze Level
Joined: 16 Oct 2009
Location: PDC, WI
Points: 191
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Nov 2010 at 9:49pm |
|
I was afraid of that.
|
|
MACK
Orange Level
Joined: 17 Nov 2009
Points: 7664
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Nov 2010 at 9:50pm |
|
As long as it is in the normal range it is ok. MACK
|
|
wjohn
Orange Level
Joined: 19 Jan 2010
Location: KS
Points: 2047
|
Post Options
Thanks(0)
Quote Reply
Posted: 09 Nov 2010 at 10:30pm |
|
My father's WD has the same problem as your 45, except Dad refuses to believe it's a problem. It still runs which to him means it must be fine. Can't say I didn't warn him!
|
|
1939 B, 1940 B, 1941 WC, 1951 WD, 1952 CA, 1956 WD-45
|
|
Glockhead SWMI
Orange Level
Joined: 12 Sep 2009
Location: South West Mich
Points: 2657
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Nov 2010 at 3:05am |
|
Oil pressure will drop some as the engine warms up. It is normal. As long as it doesn't drop too low you will be fine.
|
|
KC-WD45
Silver Level
Joined: 11 Oct 2010
Location: Kansas City
Points: 114
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Nov 2010 at 9:53am |
|
What you might think of as low might actually be normal. According to the manual 12 pounds is normal. After I rebuilt mine I was expecting to see quite a bit more than that since 12 is about at the bottom of the gauge but I was relieved to find out that 12 is what it was supposed to be. You might hook a gauge up to it and see how many pounds you have before you tear it down. Could save you a few bucks!
|
|
KY
Silver Level
Joined: 08 Dec 2009
Location: Kentucky
Points: 366
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Nov 2010 at 2:22pm |
|
Use 15-40 and a quart of lucas. Make sure tube is not stoped up or pushed down too far.
|
|
mlpankey
Orange Level
Joined: 13 Sep 2009
Location: Vols country
Points: 4580
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Nov 2010 at 3:28pm |
|
try straight weight motor oil start with 30 go to 50 weight
|
|
KY
Silver Level
Joined: 08 Dec 2009
Location: Kentucky
Points: 366
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Nov 2010 at 3:40pm |
|
That works too, any thicker oil. The lucas really made a difference in one for me.
|
|
ALinIL
Orange Level
Joined: 20 Sep 2009
Location: Frankfort, IL
Points: 316
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Nov 2010 at 4:18pm |
|
Stanley - I would check the guage. My 45 was showing "N" on the guage and when hot on a 95 degree day,the guage hardly registered. I replaced the guage with a 15# guage and have had no problems since. Cold is about 13# and on a 95 degree day its about 9-10#. - AL
|
|
pineyjd
Silver Level
Joined: 12 Sep 2009
Location: Southern NJ
Points: 100
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Nov 2010 at 3:17am |
|
My I40 showed low pressure,took tube to gauge off & cleaned,now shows 20-25,was showing 5
|
|
Stanley
Bronze Level
Joined: 16 Oct 2009
Location: PDC, WI
Points: 191
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Nov 2010 at 6:41pm |
|
Thanks for all your help.
|
|
Don(MO)
Orange Level
Joined: 12 Sep 2009
Location: Bates City MO.
Points: 6862
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Nov 2010 at 8:29pm |
Stanley take a look at this info Jim from OK Tractor posted three years or so back about oil filters. Don
|
|
3 WD45's with power steering,G,D15 fork lift,D19, W-Speed Patrol, "A" Gleaner with a 330 corn head,"66" combine,roto-baler, and lots of Snap Coupler implements to make them work for their keep.
|
|
Stanley
Bronze Level
Joined: 16 Oct 2009
Location: PDC, WI
Points: 191
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2010 at 10:18am |
|
Good information Don, Thanks. Where can I find an "old Style" filter? Any suggestions?
|
|
KY
Silver Level
Joined: 08 Dec 2009
Location: Kentucky
Points: 366
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2010 at 12:34pm |
|
Yes your agco dealer will have them. Baldwin filter co. Also makes em.
|
|
Brian Jasper co. Ia
Orange Level
Joined: 11 Sep 2009
Location: Prairie City Ia
Points: 10508
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2010 at 3:33pm |
|
Those "new" style filters should be out of the parts system by now. That's been more than a few years back if I remember correctly. I've been told that if the oil pressure gauge moves at all, they will live.
|
|
"Any man who thinks he can be happy and prosperous by letting the government take care of him better take a closer look at the American Indian." Henry Ford
|
|
bluebanshee
Silver Level
Joined: 19 Jun 2010
Points: 65
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2010 at 4:22pm |
|
I think Baldwin makes filters for Hastings so they should be the same. I have a hasting one and it is the correct type of filter. Last time I bought a filter it was cheaper at TSC than advance.
|
|
