| Author |
 Topic Search  Topic Options
|
john(MI) 
Orange Level
Joined: 12 Sep 2009
Location: SE MI
Points: 9262
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Somebody should save this sickle mower
Posted: 17 Dec 2020 at 10:57pm |
|
|
|
D14, D17, 5020, 612H, CASE 446
|
 |
|
Sponsored Links
|
|
|
festus51
Orange Level Access
Joined: 26 Mar 2017
Location: Osage City, KS
Points: 1639
|
Post Options
Thanks(0)
Quote Reply
Posted: 17 Dec 2020 at 11:12pm |
|
I remember those from being a kid. They are a pain in the butt to hook up.
|
|
We the unwilling Led by the unqualified Doing the impossible for the Ungrateful
|
|
AaronSEIA
Orange Level
Joined: 11 Sep 2009
Location: Mt Pleasant, IA
Points: 2556
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Dec 2020 at 6:09am |
80R. Not too bad to put on. That one looks pretty bent up. For $150 it'd make a real nice parts machine though. AaronSEIA
|
|
festus51
Orange Level Access
Joined: 26 Mar 2017
Location: Osage City, KS
Points: 1639
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 Dec 2020 at 6:22pm |
|
When you're 14 years old and by your self it was a pain to hook up.
|
|
We the unwilling Led by the unqualified Doing the impossible for the Ungrateful
|
|
Gary
Orange Level Access
Joined: 13 Sep 2009
Location: Peterborough,On
Points: 5445
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Dec 2020 at 9:23am |
|
I have one and there is a bit of a knack to it.
I use a 2 X 6 board and a 6 X 6 block when installing hitch on tractor.
Mower Twin Wheel Drive is sitting on a Patio Stone.
Adjust the 2 arms with Jaw Openings to correct height with Cutter Bar Tilt Crank.
Back tractor hitch in to Jaws. Connect R/H Lift Assembly.
Raise Tractor Hydraulic to top, this forces Jaws in to place to install Tapered pins.
G
|
|
Gary Burnett
Orange Level Access
Joined: 11 Sep 2009
Location: Virginia
Points: 2943
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Dec 2020 at 12:31pm |
|
Or sit the whole mower down on a couple pallets the right height and just back right in and drop in the two wedges.
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8419
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Dec 2020 at 1:34pm |
|
The ad says make offer. Don't think he would get $150 in scrap.
I know what you mean by being tricky. I also grew up with 80R and once got the hang of it, wasn't to bad.
But would rather hook that up over ether of the 3pt models
Edited by Mikez - 19 Dec 2020 at 1:51pm
|
|
AC720Man
Orange Level
Joined: 10 Oct 2016
Location: Shenandoah, Va
Points: 4951
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Dec 2020 at 9:10pm |
|
The outer shoe, guards, pto shaft are worth what he is asking for it.
|
|
1968 B-208, 1976 720 (2 of them)Danco brush hog, single bottom plow,52" snow thrower, belly mower,rear tine tiller, rear blade, front blade, 57"sickle bar,1983 917 hydro, 1968 7hp sno-bee, 1968 190XTD
|
|
