| Author |
 Topic Search  Topic Options
|
Ronnie 
Orange Level
Joined: 23 Mar 2014
Location: New Brighton
Points: 557
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: E3 engin in to wd
Posted: 22 Nov 2015 at 4:00pm |
|
Hi all I just got a e3 engine and I was wondering what all had yo be changed to bolt up to a wd.
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20528
|
Post Options
Thanks(0)
Quote Reply
Posted: 22 Nov 2015 at 7:49pm |
|
Start by removing the flywheel, starter and starter mount plate, water pump and crankshaft pulley from the E-3 engine. Use your WD flywheel and a 9-spring pressure plate from a WD-45 and a 4-button clutch disc from a Gleaner K combine. Drill out your WD water pump holes oversize and mount it to the E-3 block. You might have to bore clear thru your WD crank pulley to get it to slide on the E-3 crank nose, just depends...some do, some don't. Fan belt will run a little crooked with this set-up but for a puller, it will make no difference. Then, there's the governor control linkage to transfer over from one front cover to the other.
|
|
mattb
Orange Level
Joined: 11 Jan 2011
Points: 348
|
Post Options
Thanks(0)
Quote Reply
Posted: 23 Nov 2015 at 9:42am |
|
I put a couple washers under the waterpump pulley to space it out a little to true the belt up some, might have to tweak the oil lines by the oil filter to clear steering shaft
|
|
Charlie175
Orange Level
Joined: 11 Sep 2009
Location: Shenandoah, VA
Points: 6358
|
Post Options
Thanks(0)
Quote Reply
Posted: 23 Nov 2015 at 11:22am |
 mattb wrote:
might have to tweak the oil lines by the oil filter to clear steering shaft |
Yes!
|
|
Charlie
'48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD
|
|
Ronnie
Orange Level
Joined: 23 Mar 2014
Location: New Brighton
Points: 557
|
Post Options
Thanks(0)
Quote Reply
Posted: 26 Nov 2015 at 10:01am |
|
Ok thanks everyone
|
|
Lunker
Bronze Level
Joined: 15 Oct 2010
Points: 28
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jan 2016 at 4:02pm |
|
What is a E-3 engine? Lunker
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20528
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jan 2016 at 4:07pm |
|
Gleaner combine model E-3......not an E, a newer E.
|
|
CrestonM
Orange Level
Joined: 08 Sep 2014
Location: Oklahoma
Points: 8391
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jan 2016 at 4:31pm |
|
I've always wondered this about puller tractors...Does that extra power ever harm things in the transmission/rear end of the tractor that was made for a lower hp engine?? I know they used to have that problem in the Ford 8N's with the straight 6 and V-8 Funk conversions.
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20528
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jan 2016 at 4:50pm |
|
I'm sure if you installed a 67 flywheel HP E-3 engine in a WC chassis and farmed heavily with it, you'd eventually fail something in the transmission or rear end, but for a minute or two of tractor pulling and probably at a reduced weight compared to field weight, nothing bad ever seems to happen. In fact, there are MANY WC's well over that 67 HP figure than you can ever imagine.
|
|
patrickmull
Orange Level
Joined: 11 Jan 2011
Location: Casey IL
Points: 893
|
Post Options
Thanks(0)
Quote Reply
Posted: 03 Jan 2016 at 6:53pm |
|
I would like to have A good E3 engine
|
|
