Rebuilding the D14 backhoe/loader

            ""So your the type who would pawn your mistakes off on others.""
  Gosh Dan,,,,don't hit me no more,,,even them wet noodles sting a little,,,,,,
  I just about got the modifications done and just need one dang street ell and I'da been done,,,,,looks better and cleaned up the piping nice,,,,,
  Say,,,I 'm thinkin it might of been you that suggested that I pipe up,,,er,,,,never mind,,,,,
   Study'in on this some more,,,I think I'll install a "bypass valve" just inside the two quick couplers goin to the B/H,,,cause when I remove the B/H,,the loader will not get any pressurized fluid,,,, Would'a been better if I had made the loader the priority feed and the B/H the slave,,,,,but the loader control valve dumps straight back into the reservoir,,so,,,,,no can do,,,but I like this set-up better,,,,,

Joe maybe you can trade that valve to Les for some if them carburetor probably other motor parts he has sitting around....

Yes please.   LMAO

   Well, Guys,,Update # 99,,It has been many enjoyable days, weeks, months,, years gettin this project to this point and I am glad it is finally finished where it can go to work. Gonna load it on the trailer and take it up to the mountain place to do some clean up next week. Still thinkin bout building a bolt-on thumb for it,tho,,,The extra decals and pin stripeing that were on the industrials haven't come in yet so that will be "last job".
 I tried to re-do the piping to delete the selector valve but neither the BH or the loader would operate,,,,HMMmm,,,??? So, I relocated the selector valve where it can be reached from the BH seat as well as the tractor seat,,Works many wonderfuls now,,,,
 The rebuild of the Cessna Rotary Swing Cylinder was absolutely the biggest and most stressful job,,,but was well worth all the B,S&T's as it works so well now,,,!!!! OH,,,,one other thing,,,the swing is so forcefull,,you gotta just barely move the lever and it wants to haul azz,,,!!! There are some " 3/16" restriction orifices" in both of the 3/8" hydraulic hoses to the cylinder and I'm thinkin bout machining some new ones with smaller orifices like bout 1/4",,,,??  The Rotary swing cylinder uses 3/8" hoses , where all the other hoses are 1/2". What do the "Hydraulic Gurus" think  bout goin to 1/4" orifices,,???
 


Edited by desertjoe - 06 Oct 2016 at 9:53pm

    CHIT,,,CHIT,,,,,OK,,Charlie   ,or somebody,,a little help here, can't figure what the hay happened,,,I can't find the rotate to straighten them lopsided ones,,,looks like ole Shameless after drinkin some of his home made Black label,,,,,
   Sorry bout that,,,,,

   Hey Good Buddy,,,do you know how to"rotate" them pics that look drunk,,,????

   
  Anybody,,,???? need to rotate pics #1, 2, 3, 4, 5, and delete one of the duplicates,,Thanks,,,


Edited by desertjoe - 07 Oct 2016 at 7:57am

Hope that that is right!!!

and YOU wanted to teach me how to post pics?????? (poke,poke,poke)

desertjoe wrote:    BenGIBoy,,,you're the greatest,,DANG,,,I appreciate you,,,!!!,,,,,and,,,,and,,,you can tell ole Shameless,,,I SAID SO,,,!!!! You know I tried everything this ole man could think of,,the pics in my pic folder were ok and I even tried deleting and startin over but still would rotate,,,I even transferred them to the folder here in the correct orientation,,,but somehow the uploading was rotating em,,,and for why I know even less,,,,,,,,but,,,,    you KNEW this was coming,,,,HOW'ed you do it,,,????

     CHIT,,,pics didn't load,,,bite yer tongue,,Shameless,,,
  The "teeth" are 1/2" plate, the "main" hold-down is 2"X2"X3/8" square tubing, and the anchor points are 5/8" and 1" machined pins,,should be hell for stout,,,!!!
   CHIT,,Bengiboy,,it done it again on the last pic,,,WTF,,??? When I rt click on the pic, I don't see a "save" option,,,???
      


Edited by desertjoe - 17 Oct 2016 at 9:57am

     Hey BengiBoy,,,,,,I'm gonna figure it out ,,,,soon or late,,,,Hungry thanks you too,,,!!!

I like the thumb