allis b 3pt

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Its a press fit... You can not PUSH it in.. You have to BUMP it a little with a hammer and punch and move it .010 - .020 inch at a time..... I have made a PUNCH on the lathe out of a 3/4 inch bar that  is turned down to  3/8 inch and is 9/16 long and you can use it to BUMP the plug down until the 3/4 inch punch face bottoms out on the case... After checking pressure, you "MIGHT" have to push a little further, but normally 9/16 is close..... if the SPRING under the plug is broke or weak, that might be a problem with loss of pressure.

You might be able to use a 3/8 inch bolt with a nut screwed onto it 9/16 inch... then tap the bolt down the hole with a hammer until the NUT hits the case ?? 

Edited by steve(ill) - 22 May 2022 at 10:00pm

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
steve(ill) Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81236	Post Options Post Reply Quote steve(ill) Report Post Thanks(0) Quote Reply Posted: 22 May 2022 at 9:57pm
	Its a press fit... You can not PUSH it in.. You have to BUMP it a little with a hammer and punch and move it .010 - .020 inch at a time..... I have made a PUNCH on the lathe out of a 3/4 inch bar that is turned down to 3/8 inch and is 9/16 long and you can use it to BUMP the plug down until the 3/4 inch punch face bottoms out on the case... After checking pressure, you "MIGHT" have to push a little further, but normally 9/16 is close..... if the SPRING under the plug is broke or weak, that might be a problem with loss of pressure. You might be able to use a 3/8 inch bolt with a nut screwed onto it 9/16 inch... then tap the bolt down the hole with a hammer until the NUT hits the case ?? Edited by steve(ill) - 22 May 2022 at 10:00pm
	Like them all, but love the "B"s.

Sponsored Links

10ptjim Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 10 Apr 2022 Location: greendale Points: 23	Post Options Post Reply Quote 10ptjim Report Post Thanks(0) Quote Reply Posted: 24 May 2022 at 5:19pm
	one last question, what oil is recommended for the transmission, cant find specs in book, using hydraulic trans fluid, to thin? took pump in and they said on older red tractors the use 30 wt oil. any place to send this pump or get rebuild kit, hard to find. thanks again for all your help

steve(ill) Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81236	Post Options Post Reply Quote steve(ill) Report Post Thanks(0) Quote Reply Posted: 24 May 2022 at 9:38pm
	you are using the correct oil... Universal TRactor fluid , Hy Trans, Hydraulic Transmission fluid, etc.... all of it is about 20 wt oil. ... I dont know who rebuilds them.. I have done a few 10-20 years ago. not overly hard. Never used a lot of "new parts",, basically you just clean / polish / redo a couple seats for ball bearings ( punch them), and file a face flat if needed... book gives STEPS to disassemble and reassemble.. Yours seems to WORK, but PSI is low.. I would pull the top plug and check the relief valve DEPTH for 9/ 16 inch .... If it is close, then maybe the spring is broken below the plug.. If its not close, bump it down a 1/16 inch and see what happens ???
	Like them all, but love the "B"s.