| Author |
 Topic Search  Topic Options
|
screwylouie010 
Silver Level
Joined: 02 Jul 2013
Location: Salt Point, ny
Points: 261
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 8070 fwa spindle nut socket
Posted: 27 Dec 2023 at 3:55pm |
|
Hey. I’ve searched and searched with no luck. Can anyone tell me the size socket I need for the front spindle nuts on a fwa 8070? It’s 6 pin/slot, approx 3.25”. Closest I’ve found is for ford/Chevy pick up trucks but is only 2 5/8”. Hammer and chisel is not working. I would rather buy a socket than make 1. Anyone have a part number for the correct socket? Thanks
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20485
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Dec 2023 at 4:56pm |
|
Allis never had a "socket". They had a spanner wrench specially made just for that nut that accepted a 3/4" drive socket extension.
|
|
Ed (Ont)
Orange Level
Joined: 08 Nov 2009
Location: New Lowell, Ont
Points: 1290
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Dec 2023 at 5:22pm |
|
Go to truck shop. They will gear you up with a socket. We use them all the time for rear bearings. Lot of them are between 4-5 inches. 6 or 8 point.
|
|
Lynn Marshall
Orange Level Access
Joined: 13 Sep 2009
Location: Dana, Iowa
Points: 2283
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Dec 2023 at 7:21pm |
|
I had a really nice homemade one for sale. I don't know if I still have it. It'll be a couple of days before I can look.
|
|
MikeKroupa
Bronze Level Access
Joined: 12 Sep 2009
Location: pierce,nebraska
Points: 77
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Dec 2023 at 12:30pm |
|
Doc is correct, spanner wrench for spindle nut. I have one but not for sale.
|
|
screwylouie010
Silver Level
Joined: 02 Jul 2013
Location: Salt Point, ny
Points: 261
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Dec 2023 at 3:27pm |
|
I made what I imagine doc is describing, today. I made it out of 1/4” plate steel. I made 1/2” extension fit pretty snug in it. The extension started to back out of it then spun. Also started to round off my notch that fits into the nut. I have a 1/2” breaker bar on it. No movement from the nut. I make try to make a full socket
|
|
I M Fedup
Bronze Level
Joined: 01 Jul 2020
Location: Winchester Ky
Points: 28
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Dec 2023 at 4:22pm |
|
I made a socket for certain New Holland front hubs that use a similar design on the nut. Just a short piece of pipe the right diameter (from the scrap pile) 2" pieces of 3/8" key stock placed around it and held with hose clamps. Once I got all the pieces positioned right I welded them to the pipe. I slipped an old 3/4 drive socket into the pipe on the other end and welded it up. I've used it many times and it's never failed me.
|
|
Lynn Marshall
Orange Level Access
Joined: 13 Sep 2009
Location: Dana, Iowa
Points: 2283
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Dec 2023 at 7:22pm |
|
Those nuts are usually loctited. You have to heat the nut to get them loose.
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8239
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Dec 2023 at 9:17pm |
 Lynn Marshall wrote:
Those nuts are usually loctited. You have to heat the nut to get them loose. |
That seems like important information. Could make all the difference!
|
|
lentsch
Silver Level
Joined: 10 Feb 2011
Location: Glencoe,Mn.
Points: 212
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Dec 2023 at 9:21pm |
|
I have a socket in my tool box that I modified to work. I will get a picture or part number tomorrow.
|
|
WD,D15,190XT,7000,8010x2,7060,8070
|
|
screwylouie010
Silver Level
Joined: 02 Jul 2013
Location: Salt Point, ny
Points: 261
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Dec 2023 at 5:00pm |
|
Thank you everyone. I haven’t had time to mess with it anymore
|
|
