This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


WC Low Oil Pressure
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Dave(inMA) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Grafton, MA
Points: 2398 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave(inMA) Quote  Post ReplyReply Direct Link To This Post Topic: WC Low Oil Pressure
    Posted: 09 Sep 2024 at 10:29am
Just changed the oil (10W-30) and filter (Fram C159) in my unstyled WC. Ran it to warm up the oil just before draining the oil, and oil pressure reading was mid-range (about the "r" in "Normal") but barely into normal range after changing the oil. Oil is up to the full mark. The filter had been sitting on the shelf for several years.

The one odd thing is that the center pipe came out with the old filter. I tapped it until it "seated" when I reinstalled it. Might that be the cause of the low reading? Thanks!
WC, CA, D14, WD45
Back to Top
Sponsored Links


Back to Top
Alvin M View Drop Down
Orange Level
Orange Level


Joined: 24 Jun 2018
Location: PA
Points: 764 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Alvin M Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2024 at 11:36am
If you tap it in too far it will cut the flow to the gauge
Back to Top
ac45dave View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 23 May 2015
Location: SE(IN)
Points: 1337 		Post Options Post Options   Thanks (0) Thanks(0)   Quote ac45dave Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2024 at 11:42am
It states in the operators manual,oil press will read lower until the filter is fully saturated.With only 1/5th of the oil flowing through the filter, it takes a bit to get the press back up.
54 wd-45gas ; 56 wd-45d N/F w/fact p/s ; 63 d-17 sIII N/F gas ; 60 D14 N/F ; 67 d-17 sIV N/F gas ; 63D15 sII W/F; 39rc#667 ; 2021 massey 4710 fwa ; gravely 2 wheel tractors
Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 81092 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2024 at 1:22pm
the PRESSURE is made by BACK PRESSURE from the filter. New filters have very little restriction and therefore LESS pressure shows on the gauge... Couple good notes above.. dont push the 1/4 inch tube too deep, and let the filter saturate for 30 minutes before you get a GOOD pressure reading.. If the filter was STUFFED COTTON style like the OLD ONE then it is fine.. Being on the shelf did not hurt it.
Like them all, but love the "B"s.
Back to Top
Dave(inMA) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 12 Sep 2009
Location: Grafton, MA
Points: 2398 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave(inMA) Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2024 at 6:53pm
Thanks, guys. I pulled the center tube and reseated it higher in its hole. Pressure now reads close to the "R". I much appreciate your help!

David
WC, CA, D14, WD45
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.047 seconds.


Help Support the
Unofficial Allis Forum