This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Promised myself this wouldnt happen, but... |
Post Reply |
Author | |
morton(pa)
Orange Level Joined: 11 Sep 2009 Location: Lancaster, PA Points: 1234 |
Post Options
Thanks(0)
Posted: 14 Sep 2009 at 5:39pm |
...The engine on the '40 hand crank B got stuck while it's been sitting for the last couple months. And since I was going to get it ready to sell to a guy locally who's interested in it, this adds more work to the pile. Got any ideas on an easy way to break it free? It hasnt been setting for years and years, just maybe 9-12 months and the engine hasnt been stuck that long since I used to take the hand crank and spinn the engine once or twice a week for the first few months. So I'm open to all ideas. However I don't have any HUGE tools that might help and I'm not interested in seperating the engine from the tractor. Oh well. Thats what I get for not keeping up with keeping it loose.
|
|
Sponsored Links | |
JimD
Orange Level Joined: 11 Sep 2009 Location: Mounds, OK Points: 2112 |
Post Options
Thanks(0)
|
Penetrating oil down the cylinders. I like sea foam, some like Kroil. I wouldn't even waste time with pbblaster or wd40 etc. Let it set a few days, and give the crank a tug.
|
|
Owner of OKtractor.com PM for an instant response on parts. Open M-F 9-6 Central.
We have new and used parts. 877-378-6543 |
|
jaybmiller
Orange Level Access Joined: 12 Sep 2009 Location: Greensville,Ont Points: 22720 |
Post Options
Thanks(0)
|
I'd pull the plugs, fill the cylinders with diesel/kerosene/oil/? and walk away for a day.Then try to turn her over,gently.If it doesn't, top up the cylinders with the d/k/o and walk away again.Try turning over next day,GENTLY.Repeat as necessary until she turns over. Then blow the d/k/o out the cylinders with compressed air, put in clean plugs and fire her up.You may need to change plugs from all the oil.This is what I did with my D-14 that hthhad sat for 30+ years and she's been fine for the past 7 years. Jay
|
|
steve(ill)
Orange Level Access Joined: 11 Sep 2009 Location: illinois Points: 81928 |
Post Options
Thanks(0)
|
automatic trans fluid has some good cleaning agents in it. mix it half and half with acetone to thin it down and that make a good penetrant. I have taken off the starter and pryed on the flywheel with a long pointed bar, or jack up one back tire and jerk it forward and back couple times a day to put a load on the crank shaft. Sometimes it dont hurt to pull the valve cover off also and tap on each vavle to see that they are not stuck. Could bend a push rod.
|
|
Like them all, but love the "B"s.
|
|
GlenninPA
Orange Level Joined: 11 Sep 2009 Location: Ashley, PA Points: 5054 |
Post Options
Thanks(0)
|
Kroil in the cylinders, pull the valve cover and squirt each valve stem.
Be gentle, it should come loose.
Edited by GlenninPA - 14 Sep 2009 at 5:57pm |
|
realolman
Orange Level Joined: 12 Sep 2009 Points: 384 |
Post Options
Thanks(0)
|
loosened the rings in an engine one time with marvel mystery oil
squirted maybe a quarter cup in each cylinder with an oil can.
Edited by realolman - 14 Sep 2009 at 6:02pm |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |