This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
D17 Industrial Series III - brakes |
Post Reply |
Author | |
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
Posted: 15 Feb 2010 at 1:27pm |
What could cause the brakes to disintegrate like this?
I have new parts from Agco and have put pictures of them on my page: http://home.comcast.net/~old_allis/ac-D17-brakes.html I'd like to avoid having it happen again since the new parts are somewhat more than cheap. Thanks. Tom |
|
Sponsored Links | |
Eldon (WA)
Orange Level Joined: 11 Sep 2009 Location: Spokane, WA Points: 7765 |
Post Options
Thanks(0)
|
My guess would be the balls and plate got worn to the point they wedged together....heavy tractor, high speed, on pavement, apply brakes and POP! My D17 and 175 are too that point where the wheel occasionally locks up. It makes a scary sound and if you are in soft dirt it will spin the tractor around.....new parts should cure the problem.
|
|
ALLIS EXPRESS!
This year: |
|
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
|
Thanks, I'm hoping the new parts are the cure. The service manual I have doesn't mention the series III and IV brakes, even though it has other series IV stuff. Other than shims on the final drive side friction plate I don't see any side to side adjustment, and I don't know what the spacing should be with no brakes applied. Tom
|
|
Eldon (WA)
Orange Level Joined: 11 Sep 2009 Location: Spokane, WA Points: 7765 |
Post Options
Thanks(0)
|
Here's what the IT manual says for the 170....I'd think they would be the same.
A dimension of 2.034-2.044 inches should be maintained between the outer brake friction surface and the brake friction surface on the differential bearing carriers. To check this dimension, install final drive units without brake band or drum and disc units and measure distance between friction plate and bearing carrier brake friction surfaces with an inside micrometer. Use shims between the outer friction plate and final drive pinion shaft sleeve to obtain the correct dimension.
|
|
ALLIS EXPRESS!
This year: |
|
Gatz in NE
Orange Level Joined: 11 Sep 2009 Location: Lincoln, NE Points: 1036 |
Post Options
Thanks(0)
|
Scanned page out of I&Ts AC-201 Shop Manual.
The dimension is fairly critical.
|
|
Gatz in NE
Orange Level Joined: 11 Sep 2009 Location: Lincoln, NE Points: 1036 |
Post Options
Thanks(0)
|
The shims Eldon is referring to are Item 9 above. (Not Item 9A) and, yes... you have to make this adjustment without the brakes or disc in place.
|
|
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
|
Thanks guys, excellent information. I'm no where near ready to re-assemble things yet so I'll have to copy this out and add it to my service manual for use when the time comes. Looks like just what I was in need of. Tom
|
|
Gatz in NE
Orange Level Joined: 11 Sep 2009 Location: Lincoln, NE Points: 1036 |
Post Options
Thanks(0)
|
Also,
Get new springs...the small tapered ones with a hook on one end as per your picture.
Do not pull too hard on these when installing.
Do not use any lube on the balls or tracks....they are to stay dry and clean.
|
|
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
|
I bought those tapered springs when I got my new parts so I'm ready there. I haven't installed them yet, I'll have to make sure I don't stretch them like you said. Thanks for the no lube info too. Tom
|
|
RichinWis
Orange Level Joined: 11 Sep 2009 Location: Deforest Wis Points: 691 |
Post Options
Thanks(0)
|
Tom, Interesting to hear you have a Series III industrial! Doesn't seem to be many around, I have one also with the TS 1000 loader on it. Quite the machine. Good luck Rich
|
|
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
|
Hi Rich, I haven't seen another one like this before, the TS 1000 is quite a heavy duty loader. Is the one you have functional? Mine is in need of many things.
|
|
orangeman
Orange Level Joined: 12 Sep 2009 Points: 1751 |
Post Options
Thanks(0)
|
Tom and Rich: Can you post a pic of the D17 industrial??
Was the 1000 series loader the same as the loader on the 615 machines?
|
|
RichinWis
Orange Level Joined: 11 Sep 2009 Location: Deforest Wis Points: 691 |
Post Options
Thanks(0)
|
Tom, Yes mine is functional, although not currently a showpiece, it all works, and is my loader tractor
|
|
RichinWis
Orange Level Joined: 11 Sep 2009 Location: Deforest Wis Points: 691 |
Post Options
Thanks(0)
|
Here are some lit. pictures, I will try to find some of my tractor
|
|
RichinWis
Orange Level Joined: 11 Sep 2009 Location: Deforest Wis Points: 691 |
Post Options
Thanks(0)
|
Here is a picture of the TS1000 loader, mine does not have the hoe on it, HTH Rich
|
|
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
|
This is mine. Not much to look at yet.
Here is a link to my page for it: http://home.comcast.net/~old_allis/ac-D17.html |
|
RichinWis
Orange Level Joined: 11 Sep 2009 Location: Deforest Wis Points: 691 |
Post Options
Thanks(0)
|
Well Tom, It certainly looks like a real find to me. You will find it is a very good loader tractor. You have all the important parts except the rear wheels that are unique to the industrial. I know you will have it like new when you are done. Looks like it was a twin to mine.
|
|
orangeman
Orange Level Joined: 12 Sep 2009 Points: 1751 |
Post Options
Thanks(0)
|
Tom: I would like to make a recommendation to you regarding the front rims for this machine. The bucket that is shown in the photograph is very similar to the bucket on a 615 Industrial.
Given that the bucket will hold a capacity of 7/8 yard struck and material weights ranging from 2,000 - 3,000 pnds it would be useful for you to consider upgrading the rims from those shown in the photo's to 11L x 16 10 ply. This size rim rim (deep dish) along with the wider cross section will carry the load much better than the narrow rims illustrated in the photo. Unfortunately, I do not know who manufactured the wider deep dish rims for Allis, but they are common on all the 615 machines I have seen that were equipped with a loader. I believe the rims were optional equipment.
Just thought I would mention it. If you go with the factory rims shown on the AC literature post above, anticipate wheelpath rutting in soft conditions.
Wish you the best in your restoration!! Orangeman
|
|
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
|
Thanks for the tire size recommendation. I was thinking of going bigger too.
|
|
orangeman
Orange Level Joined: 12 Sep 2009 Points: 1751 |
Post Options
Thanks(0)
|
Tom: One other thing to consider, not sure what your plans for the loader are, but the pic you posted does not show any weight on the rear. The factory lit. posted above shows the hoe on the back which serves to offset or counter balance the weight of a bucket when loaded with material.
Recommend you consider some factory weight on the rears as well if you are not going to have a hoe on the back. This will help with the weight balance when the bucket is full.
Again, wish you the best on this D17 Industrial, hope you keep a good journal on your restoration of this machine. If you are the fellow that did the WC journal with pics, you did a swell job, I found your documentation excellent and most informative. Keep up the good work!!
|
|
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
|
I didn't get the back hoe, it had been cut off with a torch. The whole thing was going for scrap when I bought it. I have the loader off and the rest of it in the garage in several big pieces. I plan on using it as a loader tractor so I will indeed need some weight on the rear. I have taken lots of pictures but haven't made the time to update my page. My plan is to post it on my page like I did the WC and the WD45D. I was working on the RC's before this came along too and they are not getting the attention they used to either. Thanks Tom
|
|
cmpman
Bronze Level Joined: 21 Mar 2010 Location: Maine Points: 31 |
Post Options
Thanks(0)
|
HEY ALL I have a 1963 d17 indusrtial with ts1000 loader not pretty but works great new motor in it. Need info on it would love to find that industrial manual.
|
|
David Maddux
Orange Level Joined: 13 Sep 2009 Points: 2518 |
Post Options
Thanks(0)
|
Tom: You asked what the cause was that created the problem. I have had the same problem on a series3 that I had. I think a lot of the problem was mouse nest and mouse urine. It rusts things up, then when you hit the brakes hard the ball dislodges from it's socket. At least that is what mine looked like. Fix it, clean it up and adjust according to the book and it probably won't happen again as long as you own it. Dave.
|
|
David Maddux
Orange Level Joined: 13 Sep 2009 Points: 2518 |
Post Options
Thanks(0)
|
Tom: If you haven't already got new parts, you might think of finding used parts and having the discs and bands relined. I bought all of my parts for one side and then linings for the other side from Agco a few years ago and I think I had over 700.00 in that fix. Dave.
|
|
Russ-neia
Silver Level Joined: 11 Sep 2009 Location: NE Iowa Points: 489 |
Post Options
Thanks(0)
|
Some of the Gleaner combines had the 11.00 x 16 industrial style tires. Our F combine that is being salvaged where we traded it still has them. Talk to Jim-IA about it.
|
|
The innovators offer what others will imitate.
|
|
acisbest
Bronze Level Joined: 09 Oct 2009 Location: SE, PA Points: 140 |
Post Options
Thanks(0)
|
Tom,
Your work is making me feel sick.... I want to give up on my projects... Was just poking around your web site.... Such nice work, Ugh... I'm just not that good/patient. I have too many projects. I do good functional work... Your work is perfection.... Can't wait to see this D17 when its done. |
|
TomMN
Orange Level Joined: 13 Sep 2009 Location: Elbow Lake, MN Points: 858 |
Post Options
Thanks(0)
|
Thanks for the comments, but I don't have any real deadlines since this is a hobby for me. I have to say I have a great deal of respect for the folks that needed to fix these things and get them back in the field before the weather changed. It's fun to take these old things apart and see some of the stuff that was done "temporary" and stayed that way. Tom |
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |