New to pulling antiques/farm stock

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Hello getting back into pulling but not
Building another LSS for the time being. 

Bought a single front wheeled WD45 to play with. Engine stuck so will be taking it out to rebuild. Would like to put a set of D-17 piston and sleeves. If I could find a smaller stroker crank 5. To 5.5in stroke would be great. 

Few questions are
1. who to get cam and lifters from?
2. what carb to use on it? 
3. Anyone sell a drop in stroker kit? 
4. What’s a good sized tire/wheel, came with a set of 16.9x34s on pressed steel. 

	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Zachrabbit15 Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 02 Jul 2023 Location: Springfield MO Points: 7	Post Options Post Reply Quote Zachrabbit15 Report Post Thanks(0) Quote Reply Topic: New to pulling antiques/farm stock Posted: 02 Jul 2023 at 8:39pm
	Hello getting back into pulling but not Building another LSS for the time being. Bought a single front wheeled WD45 to play with. Engine stuck so will be taking it out to rebuild. Would like to put a set of D-17 piston and sleeves. If I could find a smaller stroker crank 5. To 5.5in stroke would be great. Few questions are 1. who to get cam and lifters from? 2. what carb to use on it? 3. Anyone sell a drop in stroker kit? 4. What’s a good sized tire/wheel, came with a set of 16.9x34s on pressed steel.

Sponsored Links

dgerth Members Profile Send Private Message Find Members Posts Add to Buddy List Bronze Level Joined: 27 Nov 2012 Location: NC Wash Points: 172	Post Options Post Reply Quote dgerth Report Post Thanks(0) Quote Reply Posted: 02 Jul 2023 at 11:03pm
	Allis made a very good cam as is and is hard to beat. Sky is the limit, read $$$$$$, on engines but nobody I know has a "drop-in" kit for stroker motors. Carburetors might take a while to find what will work the best for you. Start with stock or what you have and work up. As for tires, same above applies. Start with what you have and work up from there. Tractor pulling is an individual sport and what works for one does not necessarily work for another. That to me, is one of the "funner" aspects of the sport!! dg

DrAllis Members Profile Send Private Message Find Members Posts Add to Buddy List Orange Level Access Joined: 12 Sep 2009 Points: 20496	Post Options Post Reply Quote DrAllis Report Post Thanks(0) Quote Reply Posted: 03 Jul 2023 at 5:55am
	You don't seem to have a very clear plan as to what you want to do (in my opinion). What is your competition ???? You're asking about tire sizes. You're asking about camshaft grinds. You're asking about carburetor size. And finally you don't know what your engine's crankshaft stroke is. Every one of these greatly depends upon what the "rules" of whom you're pulling with will allow you to do !!! because they are all (to a degree) dependent on what RPM you can operate at. Any stroked crankshaft on an A-C engine has to be welded up and reground to whatever stroke you desire, with one exception. The stroke dictates what you might be able to use for a piston (height). The best bore is 4 1/8" as there are sleeves readily available at that size. You can stroke the crank to 4 7/8" by under cutting the rod journal to accept a two inch diameter WD45/D17/D19 diesel conn rod. The problem there is finding a piston with the right height and a .990" pin diameter to get hooked to the small end of the conn rod. I think there may be a Farmall "H" or Super "C" engine that also used a 2 inch conn rod brg that would be longer that could be made to work, Figure out what you are competing against and get a plan. Remember, you only have a two speed transmission...LOW and SECOND and there's a huge speed difference between them. Edited by DrAllis - 03 Jul 2023 at 6:06am