| Author |
 Topic Search  Topic Options
|
wildbill26 
Orange Level
Joined: 25 Sep 2010
Location: claysville,PA
Points: 534
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: no spark
Posted: 19 Jan 2014 at 2:47am |
|
ok this may be long winded but here goes. i have a b 12 that has no spark, was that way when i got it, so i put a new coil, plug, points and condencer in it. i also hard wired it insted of using the insilated lug, i cleaned up the magnets on the flywheel set both points and coil gaps per manual put it back together and still nothing, i did disconect the key switch( if i rember it just grounds it to kill spark) and still nothing, so i pulled the motor again to check the coil gap, and noticed this time there was writing on the coil that you could hardly read that said this side out, so i thought mabey i had it on wrong so i switched it around and still nothing, so im stumped. so anyone have any thoughts or sugestions? i have thought now about going to an external coil but will have to resurch that, thanks
|
|
1950 wd wide front w loader
1940 b, 1939 m crawler
|
 |
|
Sponsored Links
|
|
|
AaronSEIA
Orange Level
Joined: 11 Sep 2009
Location: Mt Pleasant, IA
Points: 2551
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jan 2014 at 7:50am |
|
I've read more than once of a new condenser being bad out of the box. Might also want to roll the engine over and make sure the point plunger is moving. Another option would be a Nova or Mega Fire solid state setup. Around $12 on eBay and no more points. You can mount it in the points box and no one will ever know. I suppose it's possible your coil or plug wire is bad too.
AaronSEIA
|
|
littlemarv
Orange Level
Joined: 10 Jun 2013
Location: Wisconsin
Points: 1829
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jan 2014 at 8:08am |
Once when I installed the points I got the retainer for the plunger boot out of place and it grounded the points, so no spark.
Something to keep in mind.......
|
|
The mechanic always wins.
B91131, WC23065, WD89101, CA29479, B1, Early B10, HB212, 416H
|
|
wildbill26
Orange Level
Joined: 25 Sep 2010
Location: claysville,PA
Points: 534
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jan 2014 at 9:34am |
|
little marve i will check that, aaron its one of those mag coils with the plug wire built into it,the plunger is working, how dose the solid state setup work? do you still need an external coil? thanks
Edited by wildbill26 - 19 Jan 2014 at 9:49am
|
|
1950 wd wide front w loader
1940 b, 1939 m crawler
|
|
wildbill26
Orange Level
Joined: 25 Sep 2010
Location: claysville,PA
Points: 534
|
Post Options
Thanks(0)
Quote Reply
Posted: 19 Jan 2014 at 9:47am |
i found the mega fire on ebay i see how it works now
|
|
1950 wd wide front w loader
1940 b, 1939 m crawler
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3539
|
Post Options
Thanks(0)
Quote Reply
Posted: 21 Jan 2014 at 1:37pm |
|
did you get any thing oily onthe points surface what part # mag did you use
|
|
