| Author |
 Topic Search  Topic Options
|
captaindana 
Orange Level
Joined: 14 Sep 2009
Location: Fort Plain, NY
Points: 2460
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: Why are every CA oil filter bases
Posted: 28 Nov 2023 at 5:17pm |
Arched like so? The oil returns to the sump where the biggest gap is and the cork gasket certainly doesn’t make up for it, or have they just warped over 72 years or is this the way they were all made? Hmmm…. on my other CA last week, I ground it pretty flat and put a new gasket. It doesn’t seem to leak just wondering. Y 
|
|
Blue Skies and Tail Winds
Dana
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20479
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 5:22pm |
|
A sharp flat file is your friend.
|
|
PaulB
Orange Level
Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4727
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 5:38pm |
 DrAllis wrote:
A sharp flat file is your friend. |
X2 Over the years the cork gasket deteriorated and when they began to leak, most thought just tight enough wasn't good enough. Everyone I've ever seen wasn't flat. No big deal just make it so.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
|
|
steve(ill)
Orange Level Access
Joined: 11 Sep 2009
Location: illinois
Points: 81066
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 5:56pm |
|
YEP... gasket gets old and HARD and leaks.. TIGHTEN the bolts and bow the base... File it flat and get a GOOD gasket and your good to go.
|
|
Like them all, but love the "B"s.
|
|
captaindana
Orange Level
Joined: 14 Sep 2009
Location: Fort Plain, NY
Points: 2460
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 8:42pm |
|
Yay thanks to all I’ve been using that file!
|
|
Blue Skies and Tail Winds
Dana
|
|
Gary
Orange Level Access
Joined: 13 Sep 2009
Location: Peterborough,On
Points: 5371
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Nov 2023 at 7:35am |
|
Same goes for the Fuel Sediment Bowl. If it starts to drip, it needs just a little more tightening, and then a little bit more again, until you now have a stream!
G
|
|
DSeries4
Orange Level
Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7332
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Nov 2023 at 2:49pm |
|
When the gasket starts to leak, people tighten them down way too much. That's what causes them to warp.
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '61 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
captaindana
Orange Level
Joined: 14 Sep 2009
Location: Fort Plain, NY
Points: 2460
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Nov 2023 at 5:13pm |
|
3 minute file = done!
|
|
Blue Skies and Tail Winds
Dana
|
|
dfwallis
Orange Level
Joined: 09 Mar 2023
Location: DFW
Points: 627
|
Post Options
Thanks(0)
Quote Reply
Posted: 29 Nov 2023 at 5:49pm |
|
I just rebuilt a 52 CA and didn't notice it being warped (surely I would have). But now I'm worried :( Anyway, it's got a new gasket and some silicone sealant on it so hopefully ok. I did have to replace the suction tube. It oddly had small rust pitted section only on one side of the tube about the middle.
|
|
