| Author |
 Topic Search  Topic Options
|
DIESEL 
Silver Level
Joined: 26 Aug 2013
Location: Sandhills
Points: 259
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: 7040 engine oil cooler reseal
Posted: 28 Nov 2023 at 2:01am |
|
Oil cooler on my 7040 needs re-sealed, can the inner tubes be tapped out with a block of wood without damaging them, I don't have a press. First time messing with one of these, thanks.
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 20479
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 2:48am |
|
Yes. We always had a 4 x 4 block re-shaped to slide in and be the pusher against the cooler core.
|
|
AllisFreak MN
Orange Level Access
Joined: 07 Dec 2009
Location: Minnesota
Points: 1541
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 6:22pm |
|
Doc what all is needed as far as parts to complete this job?
|
|
'49 A-C WD, '51 A-C WD, '63 A-C D17 Series III, 1968 A-C One-Seventy, '82 A-C 6060, '75 A-C 7040, A-C #3 sickle mower, 2 A-C 701 wagons, '78 Gleaner M2
|
|
Lynn Marshall
Orange Level Access
Joined: 13 Sep 2009
Location: Dana, Iowa
Points: 2282
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 6:55pm |
|
O rings and gaskets. Not much involved here. The cooler o rings are specific as to water side or oil side of the cooler.
|
|
Michael V (NM)
Orange Level Access
Joined: 12 Sep 2009
Location: NM
Points: 2403
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 8:10pm |
I done this on my 7060 few years back. a search of my stuff might bring it up I think the main thing is to put the o-rings in the right place
|
|
tbran
Orange Level
Joined: 14 Sep 2009
Location: Paris Tn
Points: 3291
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 8:32pm |
|
the block and cooler mating surface must be squeaky clean with a non silicone gasket sealer. That is the biggest challenge we have had.
|
|
When told "it's not the money,it's the principle", remember, it's always the money..
|
|
I M Fedup
Bronze Level
Joined: 01 Jul 2020
Location: Winchester Ky
Points: 28
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Nov 2023 at 9:50pm |
|
Assemble everything loosely, and don't tighten any bolts until it's all together on the engine. Then tighten them down a little at a time, working your way around from gasket to gasket.
|
|
DIESEL
Silver Level
Joined: 26 Aug 2013
Location: Sandhills
Points: 259
|
Post Options
Thanks(0)
Quote Reply
Posted: 04 Dec 2023 at 9:13pm |
|
Is it better to glue the gasket to the engine block or the cooler, on reassembly? Thanks
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8235
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2023 at 8:06am |
|
Don't know about better...I glued gasket to cooler
|
|
DIESEL
Silver Level
Joined: 26 Aug 2013
Location: Sandhills
Points: 259
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2023 at 12:16pm |
|
Thanks Steve, that's what I was leaning towards,Tbran mentioned having difficulty with this seal leaking, I didn't know if one was better than the other
|
|
SteveM C/IL
Orange Level Access
Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 8235
|
Post Options
Thanks(0)
Quote Reply
Posted: 05 Dec 2023 at 7:39pm |
|
I figured it may be harder to seal the slick aluminum over the cast iron block so I put the sealer there.
|
|
