This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Allis Chalmers C Thread size adaptors
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
John426 View Drop Down
Silver Level
Silver Level


Joined: 14 Aug 2012
Location: France
Points: 275 		Post Options Post Options   Thanks (0) Thanks(0)   Quote John426 Quote  Post ReplyReply Direct Link To This Post Topic: Allis Chalmers C Thread size adaptors
    Posted: 14 Jul 2024 at 8:26am
Hi

I am looking for the thread size for adaptor on the Allis C hydraulic. 

 Pump out , Ram in , Pipe , Control valve left right







Edited by John426 - 14 Jul 2024 at 8:39am
Back to Top
Sponsored Links


Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 80142 		Post Options Post Options   Thanks (0) Thanks(0)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 14 Jul 2024 at 9:46am
Ii think most of the hydraulic fittins are a 1/4 inch PIPE thread..  Noramlly the hose is 1/4 inch male pipe and the fitting in the valve / cylinder has a 1/4 inch swivel pipe fitting.

the second photo you posted says HOSE, but looks like a TUBE ???  The Allis C only used 1/4 inch PIPE and hose fittings.


Edited by steve(ill) - 14 Jul 2024 at 9:58am
Like them all, but love the "B"s.
Back to Top
steve(ill) View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: illinois
Points: 80142 		Post Options Post Options   Thanks (1) Thanks(1)   Quote steve(ill) Quote  Post ReplyReply Direct Link To This Post Posted: 14 Jul 2024 at 9:49am
most systems i have seen use this fitting that screwes into the valve/ cylinder, and has a swivel to screw to the hose... all 1/4 inch pipe.
Like them all, but love the "B"s.
Back to Top
PaulB View Drop Down
Orange Level
Orange Level


Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4663 		Post Options Post Options   Thanks (0) Thanks(0)   Quote PaulB Quote  Post ReplyReply Direct Link To This Post Posted: 14 Jul 2024 at 9:54am
Here on this side of the water, 1/4" NPT (National Pipe Taper) Is easy to find. In France you may have to go to some industrial Hydraulic place to get what you need to do what you want.
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
Back to Top
CA13414 View Drop Down
Silver Level
Silver Level


Joined: 25 Feb 2024
Location: Nebraska
Points: 258 		Post Options Post Options   Thanks (0) Thanks(0)   Quote CA13414 Quote  Post ReplyReply Direct Link To This Post Posted: 14 Jul 2024 at 6:41pm
Originally posted by steve(ill) steve(ill) wrote:

most systems i have seen use this fitting that screwes into the valve/ cylinder, and has a swivel to screw to the hose... all 1/4 inch pipe.


< id="idg-io-safe-browsing-enabled" ="" oninit="true">

Thanks!  Forgot that I need two of these!!!
Helping the aged survive and thrive! 1953 CA
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.105 seconds.


Help Support the
Unofficial Allis Forum