![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
distributer d17 series 4 vs. 175 differance? |
Post Reply ![]() |
Author | |
HudCo ![]() Orange Level ![]() ![]() Joined: 29 Jan 2013 Location: Plymouth Utah Points: 3471 |
![]() ![]() ![]() ![]() ![]() Posted: 22 May 2024 at 9:17pm |
any differance in the distributer on a d17 series 4 and a 175 mecanical advance weights or the series 1 what wiehgts or springs will be the best with the 175 cam still be the series 4 govenor weights and spring
|
|
![]() |
|
Sponsored Links | |
![]() |
|
HudCo ![]() Orange Level ![]() ![]() Joined: 29 Jan 2013 Location: Plymouth Utah Points: 3471 |
![]() ![]() ![]() ![]() ![]() |
i will be useing a pertronix but my dist. sat for at least a full year outside with out a cap on it and the mechanical advance is is rusted beond repair
|
|
![]() |
|
tbran ![]() Orange Level ![]() Joined: 14 Sep 2009 Location: Paris Tn Points: 3266 |
![]() ![]() ![]() ![]() ![]() |
The 175 distributor had different weights and springs as the RPM was higher and had a longer advance curve. 70232828 70232829 springs and wts. These were with screw type dist cap mostly - E's and 175's. Both were Delco so will interchange. 240001 is the sn break. I have seen a lot of swaps...
Edited by tbran - 23 May 2024 at 3:19pm |
|
When told "it's not the money,it's the principle", remember, it's always the money..
|
|
![]() |
|
HudCo ![]() Orange Level ![]() ![]() Joined: 29 Jan 2013 Location: Plymouth Utah Points: 3471 |
![]() ![]() ![]() ![]() ![]() |
will those weights 70232828 and 70232829 fit in the series 1 distributer ? wonder what combination i want with the d17 rpms and the 175 cam ?
|
|
![]() |
|
tbran ![]() Orange Level ![]() Joined: 14 Sep 2009 Location: Paris Tn Points: 3266 |
![]() ![]() ![]() ![]() ![]() |
Due to the nature of theLow RPMs don't think it will matter - you need to tune it on a dyno and adjust the timing to max hp. Having done this it is amazing how much one can adjust the distributor with no noticable difference. When the timing is retarded the rpms go down and then come back when advanced to the point of pinging - then back off. You can't determine the start of 'pinging' by ear. Depending on compression, air flow and other issues timing will probably be different than factory specs for your purpose.
|
|
When told "it's not the money,it's the principle", remember, it's always the money..
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |