![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Pistons |
Post Reply ![]() |
Author | |
Ol case mike ![]() Bronze Level ![]() ![]() Joined: 24 Dec 2022 Location: Michigan Points: 7 |
![]() ![]() ![]() ![]() ![]() Posted: 23 Apr 2024 at 1:21pm |
Is there enough room to install wd 4-1/8 power crater pistons onto a gleaner z these are not wd45 power crater pistons I know sp46 need to be machined some to clear I was just wondering about the power craters
|
|
![]() |
|
Sponsored Links | |
![]() |
|
DrAllis ![]() Orange Level Access ![]() Joined: 12 Sep 2009 Points: 20107 |
![]() ![]() ![]() ![]() ![]() |
M & W piston kit SP-46 fits the 4 inch stroke WC/WD engines and have a Power Crater type bowl in them. If you install them in a WD45 or D-17 engine with the 4 1/2" stroke you need to machine .170" off the top so they don't smack the cylinder head. As far as what you're wanting to use, I have no idea what the compression distance/height is. Might work. Might not.
|
|
![]() |
|
Ol case mike ![]() Bronze Level ![]() ![]() Joined: 24 Dec 2022 Location: Michigan Points: 7 |
![]() ![]() ![]() ![]() ![]() |
I have both sets MW 4-1/8
And the smooth bowl I thought them was called power crater that is also 4-1/8 set I was thinking about putting the smooth bowl into a gleaner z code I don’t know either pin height both are still in motors with wd cranks I was just wondering if the smooth bore needed any machine work to be installed like the sp46 piston needs it’s for a unstyled wc pulling tractor that has a stock z gleaner |
|
![]() |
|
DrAllis ![]() Orange Level Access ![]() Joined: 12 Sep 2009 Points: 20107 |
![]() ![]() ![]() ![]() ![]() |
In the "KNOWLEDGE" section of this website, down near the bottom of page 1, you will find "Compression ratio calculator for 226 engines".....good info for you.
|
|
![]() |
|
HudCo ![]() Orange Level ![]() ![]() Joined: 29 Jan 2013 Location: Plymouth Utah Points: 3471 |
![]() ![]() ![]() ![]() ![]() |
got ross duplicating some sp46 pistons (should be done any day now )for me as we speak thanks to steve fischer getting me a piston they are going in my d17 series 4 engine
|
|
![]() |
|
HudCo ![]() Orange Level ![]() ![]() Joined: 29 Jan 2013 Location: Plymouth Utah Points: 3471 |
![]() ![]() ![]() ![]() ![]() |
they will be a two ring piston and lighten alittle bit
|
|
![]() |
|
DrAllis ![]() Orange Level Access ![]() Joined: 12 Sep 2009 Points: 20107 |
![]() ![]() ![]() ![]() ![]() |
And .170" shorter ??
|
|
![]() |
|
HudCo ![]() Orange Level ![]() ![]() Joined: 29 Jan 2013 Location: Plymouth Utah Points: 3471 |
![]() ![]() ![]() ![]() ![]() |
no i decided to leave them the same pin to top hieght, and mill them at the machine shop
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |