	This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
	The Forum	Parts and Services	Unofficial Allis Store	Tractor Shows	Serial Numbers	History

Forum Home > Allis Chalmers > Farm Equipment

Forum Options

Create New Topic

New Posts

FAQ

Farm Equipment

New Topic

Show Topics

Page <1 234 5 1850 >

	Topics / Topic Starter Rating	Replies	Views	Last Post
Forum Topics
	6060 FWA front rims By K bockting, 20 Mar 2025 at 9:30pm	1	266	By Ray54 21 Mar 2025 at 12:08pm
	Chopper question By im4racin, 18 Mar 2025 at 8:53pm	6	687	By ac-mike 21 Mar 2025 at 11:17am
	8000 Series Sanden Conversion By pdh, 29 Apr 2017 at 3:37pm	7	1061	By SteveM C/IL 21 Mar 2025 at 8:37am
	Wheel weights By Brent7814, 20 Mar 2025 at 8:09am	4	385	By Darb210 21 Mar 2025 at 7:43am
	MF vs AGCO By Unit3, 20 Mar 2025 at 8:27pm	2	392	By jvin248 20 Mar 2025 at 11:15pm
	653 Parts By Vinnys21, 20 Mar 2025 at 5:36pm	1	916	By Gary 20 Mar 2025 at 7:41pm
	A brand new 1967 One-Ninety XT By Oldoug, 19 Mar 2025 at 9:35pm	5	707	By Unit3 20 Mar 2025 at 7:22pm
	Looking for a Two-Ten By Oldoug, 18 Mar 2025 at 1:05pm	12	1078	By Dale Hardtke 20 Mar 2025 at 6:45pm
	8050 blower motor By randy, 17 Mar 2025 at 2:51pm	4	525	By 8070nc 20 Mar 2025 at 3:55pm
	1965 190XT tachometer question. By 6wheeler, 11 Mar 2025 at 2:17pm	8	693	By DSeries4 20 Mar 2025 at 3:39pm
	Front wheel bearing seal By AveryD12, 18 Mar 2025 at 12:55pm	13	532	By AveryD12 19 Mar 2025 at 12:15pm
	I need some help or advice By C15TA, 12 Mar 2025 at 9:06pm	13	1547	By C15TA 19 Mar 2025 at 11:30am
	1960 Roto-baler with Overdrive By wjohn, 04 Feb 2025 at 7:47pm 1 2	37	3040	By dr p 19 Mar 2025 at 6:19am
	D-15 start push button By edmo, 03 Jan 2025 at 5:43pm 1 2	52	2753	By EPALLIS 18 Mar 2025 at 9:20pm
	engine weigh By smokyblaq, 15 Mar 2025 at 7:45am	12	675	By ToddnwIl 18 Mar 2025 at 8:24pm
	D17 steering leak By 71cgrave, 11 Mar 2025 at 10:03pm	13	811	By AC720Man 18 Mar 2025 at 2:03pm
	CA hand clutch-What are my options? By J&J, 15 Mar 2025 at 5:43pm	5	637	By J&J 18 Mar 2025 at 5:45am
	Searching for Superbeast By MarszGrain, 17 Mar 2025 at 5:27pm	2	575	By Mikez 18 Mar 2025 at 12:12am
	8000 steering By aunt allis, 17 Mar 2025 at 9:43am	6	396	By aunt allis 17 Mar 2025 at 10:39pm
	D-14 Governor Spring and Clutch pedal spring By MBAllisJF, 17 Mar 2025 at 12:59pm	2	214	By MBAllisJF 17 Mar 2025 at 5:48pm
	D-17 Series Iv Brake Pedal bushings. By KY D-17, 16 Mar 2025 at 11:11am	3	365	By Stan R 17 Mar 2025 at 4:30pm
	Old Photo of my tractor near Pewamo MI By AC WD45, 16 Nov 2023 at 5:54am	8	1450	By Stan R 17 Mar 2025 at 1:56pm
	200 PD high/low range By dnel45, 15 Mar 2025 at 12:42pm	10	729	By Ky.Allis 17 Mar 2025 at 12:53pm
	My Persian Orange #1 Journey By W12x40, 21 Nov 2024 at 8:55am	15	1485	By W12x40 17 Mar 2025 at 9:57am
	PTO shaft/transmission leak on a WD45 By WD45thingonlyruns, 11 Mar 2025 at 1:27pm	14	798	By WD45thingonlyruns 17 Mar 2025 at 8:36am
	426 Limitations/Flaws By joe, 15 Mar 2025 at 10:06am	19	1237	By tbran 17 Mar 2025 at 8:07am
	ca hand clutch By rilenz, 15 Mar 2025 at 5:45am	2	328	By rilenz 17 Mar 2025 at 7:38am
	7060 Toolbox location By Wot, 17 Mar 2025 at 5:25am	1	276	By DrAllis 17 Mar 2025 at 6:17am
	Snap-coupler lift latches LEFT/RIGHT By DrAllis, 13 Mar 2025 at 7:56pm	23	1135	By Robert Musgrave 16 Mar 2025 at 7:21pm
	Quick Hitch By Codger, 16 Mar 2025 at 7:48am	9	503	By Codger 16 Mar 2025 at 6:56pm

New Topic

Page <1 234 5 1850 >

Forum Jump

Forum Permissions View Drop Down

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum

Your browser does not support inline frames or is currently configured not to display inline frames.