This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Pulling Forum
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Wd engine build help
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Free37 View Drop Down
Bronze Level
Bronze Level


Joined: 02 Jun 2014
Location: Knoxville tn
Points: 10 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Free37 Quote  Post ReplyReply Direct Link To This Post Topic: Wd engine build help
    Posted: 02 Jun 2014 at 8:12am
I'm build a wd with the 45 crank and it is stroked 5/8 with farmall c rods I need to figure out what pistons to us I have 4.125 sleeves. Thanks
Back to Top
Sponsored Links


Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20551 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 02 Jun 2014 at 10:39pm
With the crankshaft installed in the block and one connecting rod installed on the crankshaft, measure down from the top deck as to where the piston pin center is located at TDC. Then, you need to decide what compression ratio you want and calculate from there.
Back to Top
Free37 View Drop Down
Bronze Level
Bronze Level


Joined: 02 Jun 2014
Location: Knoxville tn
Points: 10 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Free37 Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2014 at 8:11am
What is a good compression ratio for 110 octane
Back to Top
bigcountry48 View Drop Down
Orange Level
Orange Level
Avatar

Joined: 28 Aug 2011
Location: Georgia
Points: 1100 		Post Options Post Options   Thanks (0) Thanks(0)   Quote bigcountry48 Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2014 at 8:34am
11:1 would probably be the best choice, not too much stress on the motor and it will run that octane.

Edited by bigcountry48 - 03 Jun 2014 at 8:34am
1950 B, 1952 pulling wd, and 1954 wd45
Back to Top
Free37 View Drop Down
Bronze Level
Bronze Level


Joined: 02 Jun 2014
Location: Knoxville tn
Points: 10 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Free37 Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2014 at 3:07pm
Does anybody have an ideal for pistons on this engine
Back to Top
Fields View Drop Down
Orange Level
Orange Level
Avatar

Joined: 25 Apr 2011
Location: Reedsburg, Wi
Points: 359 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Fields Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2014 at 9:25pm
Is a farmall c rod 8 inch center to center. You can figure a cr. Needed with pistons. Deck high is like 12.625 inches. Take half your stroke. The rod length and the piston pin higth . Remember your allis head is flat. So any combustion chamber will be in the piston or the space between the piston and the head. Not for sure on the head gasket thickness but felpro one is ? .043 ?.
Back to Top
Free37 View Drop Down
Bronze Level
Bronze Level


Joined: 02 Jun 2014
Location: Knoxville tn
Points: 10 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Free37 Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2014 at 9:28pm
The rod is 7.250 center to center
Back to Top
Fields View Drop Down
Orange Level
Orange Level
Avatar

Joined: 25 Apr 2011
Location: Reedsburg, Wi
Points: 359 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Fields Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jun 2014 at 9:43pm
I got bored. So here is a Ih 8 cylinder or 4 cylinder truck engine piston that might work. http://www.summitracing.com/parts/slp-h996cp/overview/
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum