This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


wd governor question
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
dsgraf View Drop Down
Silver Level
Silver Level


Joined: 14 Sep 2010
Location: vermilion oh
Points: 73 		Post Options Post Options   Thanks (0) Thanks(0)   Quote dsgraf Quote  Post ReplyReply Direct Link To This Post Topic: wd governor question
    Posted: 20 Feb 2011 at 9:08pm
Just did a bunch of work on my 53 wd so it has been sitting awhile (3-4 months) in the barn. rebuilt the carb, new manifold, rebuilt generator to 12 volt, anyway started it up today and the governor is acting up. I only have idle and full trottle on the lever. In between just stays at what it was last at. I know nothing about governors. The throttle linkage was moved from the carb side while removing and installing the carb, could I have broke something inside the governor? Also noticed at start up that the head gasket is seeping oil but no antifreeze in the oil, is this normal or now do I need to replace the head gasket. what is the best way to fix governor and are parts out there for it. I have a mag on it now but have a distributer that I am getting ready to install from later wd. help? 
Back to Top
Sponsored Links


Back to Top
Steve M C/IL View Drop Down
Orange Level
Orange Level


Joined: 01 Jul 2010
Location: shelbyville IL
Points: 691 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Steve M C/IL Quote  Post ReplyReply Direct Link To This Post Posted: 20 Feb 2011 at 9:46pm
Don't know about the gov but I doubt you harmed anything in there while fiddling with the carb linkage.I suggest tightening the head bolts for the "leak".You'll likely have to remove the rocker shaft to get on some bolts but simple enough.You need to readjust valve lash anyway after retorque.Old AC book says 65 ft/lb.
Back to Top
dsgraf View Drop Down
Silver Level
Silver Level


Joined: 14 Sep 2010
Location: vermilion oh
Points: 73 		Post Options Post Options   Thanks (0) Thanks(0)   Quote dsgraf Quote  Post ReplyReply Direct Link To This Post Posted: 20 Feb 2011 at 10:10pm
thanks, Any idea where to buy parts for the governor I can't find anything anywhere. This is one thing I never wanted to work on!!!
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21051 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 20 Feb 2011 at 10:35pm
You said rebuilt the carb?? then I'm going to guess either the gov linkage isn't adjsuted properly OR the seal on the carb throttle shaft is too tight and binding, causing high effort to move the carb throttle shaft lever.
Back to Top
dsgraf View Drop Down
Silver Level
Silver Level


Joined: 14 Sep 2010
Location: vermilion oh
Points: 73 		Post Options Post Options   Thanks (0) Thanks(0)   Quote dsgraf Quote  Post ReplyReply Direct Link To This Post Posted: 21 Feb 2011 at 4:15am
what is the proper way to adjust the linkage? I did install a new manifold which is not exactly the same as the stock one that was on it so Im sure the carb moved some. I will check for the binding. I did notice while putting it back together that the linkage was very hard to move. I never remembered it being that way before?
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 21051 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 21 Feb 2011 at 6:01am
Carb/governor linkage has to be very free....figure out what your binding is. The cotter pin goes towards the water pump on the link rod at the governor arm....some people install it backwards and then it causes trouble on the carb end.
Back to Top
sandylakeimplement View Drop Down
Orange Level
Orange Level
Avatar

Joined: 18 Sep 2009
Location: Sandy Lake, PA
Points: 399 		Post Options Post Options   Thanks (0) Thanks(0)   Quote sandylakeimplement Quote  Post ReplyReply Direct Link To This Post Posted: 21 Feb 2011 at 11:57am
I am betting on the carburetor throttle shaft seal being too tight as Dr. suggested.  We can provide gov parts if needed. Bill
Sandy Lake Implement
Sandy Lake, PA
724-376-2489
www.sandylakeimp.com
FIND US ON FACEBOOK
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.109 seconds.


Help Support the
Unofficial Allis Forum