This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Install new sediment bowl on WD45
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
StanGreen View Drop Down
Bronze Level
Bronze Level


Joined: 13 Nov 2022
Location: US
Points: 49 		Post Options Post Options   Thanks (0) Thanks(0)   Quote StanGreen Quote  Post ReplyReply Direct Link To This Post Topic: Install new sediment bowl on WD45
    Posted: 24 Jul 2024 at 9:36pm
I am trying to install a new sediment bowl on a WD45 tank I am restoring, but it does not screw into the tank. I get one or two turns and it stops. I had an old sediment bowl from a WD45 and it also would not screw into the tank. Since it was an old one, I threaded it to 5/8 - 18. This did take off some metal. It now fits. I hate to mess with the new one unless there is no way around it. I cannot find anything in the shop manual or service manual on this topic. I do not want to force it and make it worse. The last thing I want is a gas leak!
Any thoughts on how to get this sediment bowl installed?
Back to Top
Sponsored Links


Back to Top
plummerscarin View Drop Down
Orange Level Access
Orange Level Access


Joined: 22 Jun 2015
Location: ia
Points: 3477 		Post Options Post Options   Thanks (0) Thanks(0)   Quote plummerscarin Quote  Post ReplyReply Direct Link To This Post Posted: 24 Jul 2024 at 10:43pm
The tank and sediment is threaded in a tapered pipe thread size. ⅜ NPT (National Pipe Thread)

Edited by plummerscarin - 24 Jul 2024 at 10:44pm
Back to Top
HudCo View Drop Down
Orange Level
Orange Level
Avatar

Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3542 		Post Options Post Options   Thanks (0) Thanks(0)   Quote HudCo Quote  Post ReplyReply Direct Link To This Post Posted: 24 Jul 2024 at 10:51pm
just run your npt taper tap up alittle farther if it isnt to lateit probley needed the threads cleared anyways 
Back to Top
JCSinPITTS,PA View Drop Down
Silver Level
Silver Level


Joined: 14 Sep 2009
Points: 229 		Post Options Post Options   Thanks (0) Thanks(0)   Quote JCSinPITTS,PA Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jul 2024 at 7:10am
be warned!!!  i bought two from a national tractor parts supplier and both leaked!  they sent me one replacement and it leaked.  i then purchased two from a local small dealer and they dont leak. i tore one of the leakers apart and was able to stop it from leaking but never put on since the one i installed was OK.  i was trying to save $$ and bought the cheaper one first and then did the job like 3-4 times
Back to Top
Gary Burnett View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: Virginia
Points: 2939 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary Burnett Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jul 2024 at 7:29am
Originally posted by JCSinPITTS,PA JCSinPITTS,PA wrote:

be warned!!!  i bought two from a national tractor parts supplier and both leaked!  they sent me one replacement and it leaked.  i then purchased two from a local small dealer and they dont leak. i tore one of the leakers apart and was able to stop it from leaking but never put on since the one i installed was OK.  i was trying to save $$ and bought the cheaper one first and then did the job like 3-4 times


Better yet just pipe the gas line out of the tank with 3/8 pipe and install an in line filter.Anything in the tank will come thru the line and go into the filter,just change filter and good to go.
Back to Top
Alberta Phil View Drop Down
Orange Level
Orange Level
Avatar

Joined: 13 Sep 2009
Location: Alberta, Canada
Points: 3776 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Alberta Phil Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jul 2024 at 8:19am
The problem with that is there is no way to stop the fuel from draining out through the carb if the needle doesn't seat  properly in the carb.  Unless you fit a shutoff valve in the line.
Back to Top
DrAllis View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Points: 20528 		Post Options Post Options   Thanks (0) Thanks(0)   Quote DrAllis Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jul 2024 at 8:29am
The lack of a sediment "bowl" doesn't give you a water trap either. The in-line filter just lets the water run on thru to the carburetor.
Back to Top
StanGreen View Drop Down
Bronze Level
Bronze Level


Joined: 13 Nov 2022
Location: US
Points: 49 		Post Options Post Options   Thanks (0) Thanks(0)   Quote StanGreen Quote  Post ReplyReply Direct Link To This Post Posted: 25 Jul 2024 at 8:05pm
Thanks for the quick reply. I had to order the tap as I do not have that one. So, next week I will give it a spin. (pun intended)Tongue
Back to Top
Gary Burnett View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: Virginia
Points: 2939 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary Burnett Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jul 2024 at 6:46am
Originally posted by DrAllis DrAllis wrote:

The lack of a sediment "bowl" doesn't give you a water trap either. The in-line filter just lets the water run on thru to the carburetor.
Of course install the filter and line so the filter is the lowest point in the line then the water can be easily seen in the filter eventually water will swell the filter shut then just replace the
$1 filter.I've had water come thru sediment bowls anyway.
Back to Top
Gary Burnett View Drop Down
Orange Level Access
Orange Level Access
Avatar

Joined: 11 Sep 2009
Location: Virginia
Points: 2939 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Gary Burnett Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jul 2024 at 6:48am
[QUOTE=Alberta Phil]The problem with that is there is no way to stop the fuel from draining out through the carb if the needle doesn't seat  properly in the carb.  Unless you fit a shutoff valve in the line.
[/QUOTE

I always install an in line cut off
Back to Top
Alberta Phil View Drop Down
Orange Level
Orange Level
Avatar

Joined: 13 Sep 2009
Location: Alberta, Canada
Points: 3776 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Alberta Phil Quote  Post ReplyReply Direct Link To This Post Posted: 26 Jul 2024 at 9:50am
Thanks, Gary.  Always a good idea to have some way to shut off the flow in case of carb malfunction.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.125 seconds.


Help Support the
Unofficial Allis Forum