This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


How to Remove wd45 hand clutch shaft

 Post Reply Post Reply
Author
Message
dr p View Drop Down
Orange Level
Orange Level


Joined: 24 Feb 2019
Location: new york
Points: 998
Post Options Post Options   Thanks (0) Thanks(0)   Quote dr p Quote  Post ReplyReply Direct Link To This Post Topic: How to Remove wd45 hand clutch shaft
    Posted: 30 Jun 2022 at 8:20pm
I have a lot of slop in my hand clutch lever so I pulled the lever. It needs two new bushings but the shaft is badly worn as well and will need to be replaced. I know the shaft is frictional fit. I can get it to spin with a pipe wrench and a cheater bar but anyone got any ideas how to get it out?
Back to Top
Sponsored Links


Back to Top
MACK View Drop Down
Orange Level
Orange Level


Joined: 17 Nov 2009
Points: 7664
Post Options Post Options   Thanks (0) Thanks(0)   Quote MACK Quote  Post ReplyReply Direct Link To This Post Posted: 30 Jun 2022 at 9:15pm
Pull right frame, weld nut the size of your slide hammer to end of shaft, and pull it out.                              MACK
Back to Top
Lon(MN) View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Elk River,MN
Points: 1902
Post Options Post Options   Thanks (0) Thanks(0)   Quote Lon(MN) Quote  Post ReplyReply Direct Link To This Post Posted: 01 Jul 2022 at 7:27am
I take the shift tower off and pound it out from the inside.
http://lonsallischalmers.com
Back to Top
SteveM C/IL View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 7907
Post Options Post Options   Thanks (0) Thanks(0)   Quote SteveM C/IL Quote  Post ReplyReply Direct Link To This Post Posted: 01 Jul 2022 at 1:14pm
I had no luck driving out from inside. 
Back to Top
dr p View Drop Down
Orange Level
Orange Level


Joined: 24 Feb 2019
Location: new york
Points: 998
Post Options Post Options   Thanks (0) Thanks(0)   Quote dr p Quote  Post ReplyReply Direct Link To This Post Posted: 01 Jul 2022 at 7:11pm
Tried Mack's idea and snapped the shaft.
Back to Top
dr p View Drop Down
Orange Level
Orange Level


Joined: 24 Feb 2019
Location: new york
Points: 998
Post Options Post Options   Thanks (0) Thanks(0)   Quote dr p Quote  Post ReplyReply Direct Link To This Post Posted: 02 Jul 2022 at 8:39pm
Ended up drilling a 7/16 hole though the shaft near the housing and VERY SLOWLY pulled it out. Took a ray Wylie Hubbard and a Tom h hall CD to get it out. Got advice on putting new one in. Think I will chill it in dry ice
Back to Top
SteveM C/IL View Drop Down
Orange Level Access
Orange Level Access


Joined: 12 Sep 2009
Location: Shelbyville IL
Points: 7907
Post Options Post Options   Thanks (0) Thanks(0)   Quote SteveM C/IL Quote  Post ReplyReply Direct Link To This Post Posted: 02 Jul 2022 at 11:22pm
have something between it and the hammer or you'll end up swelling the end
Back to Top
dr p View Drop Down
Orange Level
Orange Level


Joined: 24 Feb 2019
Location: new york
Points: 998
Post Options Post Options   Thanks (0) Thanks(0)   Quote dr p Quote  Post ReplyReply Direct Link To This Post Posted: 03 Jul 2022 at 6:30am
Thanks everyone
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum