This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Construction and other equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


HD11-B Final drive

 Post Reply Post Reply
Author
Message
wilbur 76 View Drop Down
Bronze Level
Bronze Level


Joined: 19 Jul 2021
Location: australia
Points: 3
Post Options Post Options   Thanks (0) Thanks(0)   Quote wilbur 76 Quote  Post ReplyReply Direct Link To This Post Topic: HD11-B Final drive
    Posted: 22 Jul 2021 at 6:05am
hi from Australia. I have not long owned a hd11 b and while playing around with the steer clutches  it made a crunching sound on the right side. After draining final drive oil it had metal in it so I took the cap of the the sprocket and there was more metal. looking in parts book that came with it  were some  notes that have been written and all so pant does not match  it has had some work done on drive  at some stage.  I am thinking the sprocket shaft and drive gear splines are worn.  being this is a 60 year old dozer can I pull the back cover plate off and weld the shaft to the drive gear? if this is the problem or do I keep using it like it is until it either  finish the job I brought it for or it lets go and then fix. will it do any more damage ? It will still spin both tracks pushing at this stage. Parts if I can find them are going to be second hand and probably well worn. thanks scott
Back to Top
Sponsored Links


Back to Top
gemdozer View Drop Down
Orange Level
Orange Level


Joined: 17 Sep 2009
Points: 940
Post Options Post Options   Thanks (0) Thanks(0)   Quote gemdozer Quote  Post ReplyReply Direct Link To This Post Posted: 22 Jul 2021 at 7:17am
You should never weld inside final drive parts because it will brook again a couple hours later and make more damages.
                                
Back to Top
CAL(KS) View Drop Down
Orange Level
Orange Level


Joined: 18 Sep 2009
Location: Chapman, KS
Points: 3716
Post Options Post Options   Thanks (0) Thanks(0)   Quote CAL(KS) Quote  Post ReplyReply Direct Link To This Post Posted: 22 Jul 2021 at 9:01am
i wouldnt think those parts that hard to find.  I think quite a few made it over there.

Me -C,U,UC,WC,WD45,190XT,TL-12,145T,HD6G,HD16,HD20

Dad- WD, D17D, D19D, RT100A, 7020, 7080,7580, 2-8550's, 2-S77, HD15
Back to Top
wilbur 76 View Drop Down
Bronze Level
Bronze Level


Joined: 19 Jul 2021
Location: australia
Points: 3
Post Options Post Options   Thanks (0) Thanks(0)   Quote wilbur 76 Quote  Post ReplyReply Direct Link To This Post Posted: 23 Jul 2021 at 4:20am
thanks for the reply's I have spent a couple of hours pushing fallen timber with out any problems. just trying not  to get stuck some where it can not be worked on if it lets go.  tractor is a allis chalmers hd11 wet clutch direct drive 10001 and up serial number.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.078 seconds.


Help Support the
Unofficial Allis Forum