This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Allis Chalmers > Farm Equipment
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


Question on Seal Change
 Post Reply Post Reply
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
wessel06 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 01 Aug 2010
Location: Iowa
Points: 46 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wessel06 Quote  Post ReplyReply Direct Link To This Post Topic: Question on Seal Change
    Posted: 01 Aug 2010 at 2:38pm

I have a 190XT and the rear axle seals are out and I have the tractor jacked up but i dont know how to get the tire and hub off of the axle... To me it looks like all I should have to do is take the 3 bolts out and beat the tire hub back so the hub piece surrounding the axle isn't squeezed tight on the axle... There are two key locks also and dont know if they need to be removed before or can stay in place. I'm confused and frustrated and I need the tractor back out in the hay fields. Thank you in advance to anyone who can give me pointers.
Back to Top
Sponsored Links


Back to Top
Skyhighballoon(MO) View Drop Down
Orange Level
Orange Level
Avatar

Joined: 11 Sep 2009
Location: Pilot Grove, MO
Points: 3115 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Skyhighballoon(MO) Quote  Post ReplyReply Direct Link To This Post Posted: 01 Aug 2010 at 2:51pm
I'm not an expert on this but it has been discussed before on the forum.  These prior posts might help.   Mike

http://www.allischalmers.com/new/forum/forum_posts.asp?TID=14788&KW=pusher+bolts&PID=110783&title=220-axle-wedge-stuck#110783

http://www.allischalmers.com/new/forum/forum_posts.asp?TID=8566&KW=pusher+bolts&PID=67289&title=d19-cast-wheels#67289
1981 Gleaner F2 Corn Plus w 13' flex
1968 Gleaner EIII w 10' & 330
1969 180 gas
1965 D17 S-IV gas
1963 D17 S-III gas
1956 WD45 gas NF PS
1956 All-Crop 66 Big Bin
303 wire baler, 716H, 712H mowers
Back to Top
Wade (IA) View Drop Down
Silver Level
Silver Level
Avatar

Joined: 12 Sep 2009
Location: Osceola, IA
Points: 232 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Wade (IA) Quote  Post ReplyReply Direct Link To This Post Posted: 01 Aug 2010 at 3:14pm
Yep, install the pusher bolts in the proper holes, snug them up tight, and hit on the end of axle with the largest sledge hammer you can find. 
Back to Top
wessel06 View Drop Down
Bronze Level
Bronze Level
Avatar

Joined: 01 Aug 2010
Location: Iowa
Points: 46 		Post Options Post Options   Thanks (0) Thanks(0)   Quote wessel06 Quote  Post ReplyReply Direct Link To This Post Posted: 01 Aug 2010 at 9:51pm

thank you for the help... i found bolts that thread in but not long enough so im gonna go the the blacksmith in town and have him use a lathe to take off threads on bolts that are long enough. that should work to make my own. thanks again.
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.049 seconds.


Help Support the
Unofficial Allis Forum