| Author |
 Topic Search  Topic Options
|
pinball 
Orange Level Access
Joined: 28 May 2014
Location: missouriu
Points: 6102
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: motor starting speed
Posted: 08 Nov 2018 at 1:51pm |
|
I have an h4 gasser that when you start it it starts at idle speed of which i like. it has an accelerator pedal so I can give it more gas if needed and let off of it to shift. I also have a diesel but its the opposite . it starts wide open and the foot pedal decelerates the motor speed. I would rather the diesel would start at idle speed. how or can I change it or should I. thanks for reading. norm
|
 |
|
Sponsored Links
|
|
|
CAL(KS)
Orange Level
Joined: 18 Sep 2009
Location: Chapman, KS
Points: 3786
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2018 at 2:05pm |
|
im not familiar with the H4 but any dozer i have been around with a decelerator has a hand throttle to set engine speed and the pedal is use decelerate for direction changes, gear changes and obstructions etc.
|
|
Me -C,U,UC,WC,WD45,190XT,TL-12,145T,HD6G,HD16,HD20
Dad- WD, D17D, D19D, RT100A, 7020, 7080,7580, 2-8550's, 2-S77, HD15
|
|
NomoreJohnDeere
Silver Level
Joined: 24 Jul 2017
Location: Missouri Ozarks
Points: 308
|
Post Options
Thanks(0)
Quote Reply
Posted: 08 Nov 2018 at 4:12pm |
|
look to see if the lever has a different position it can go into on the linkage
leverage a different cam action out of the linkage
|
|
HD3
|
|
DaveKamp
Orange Level Access
Joined: 12 Apr 2010
Location: LeClaire, Ia
Points: 5754
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 Nov 2018 at 4:38pm |
What Cal said... common standard for tracked machines and some cranes and even a few farm tractors, is to have the pedal setup as 'decellerator'.
That's done because the feet are busy operating other aspects of the machine, the decel pedal is only depressed to momentarily throttle down for a gearbox operation.
I think the governed speed setting would have a 'start' position... but hard to say... I just hold the D pedal down... but yeah, in the cold, it's better to not let it go straight to the sky 'till after the oil is free to move about the cabin...
|
|
Ten Amendments, Ten Commandments, and one Golden Rule solve most every problem. Citrus hand-cleaner with Pumice does the rest.
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 41568
|
Post Options
Thanks(0)
Quote Reply
Posted: 11 Nov 2018 at 6:45pm |
|
When going to start the HD4 set throttle on left council to desired speed range - then start - fwd/rev lever in neutral and other lever is throttle so adjust to low setting on starting
|
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
|
|
pinball
Orange Level Access
Joined: 28 May 2014
Location: missouriu
Points: 6102
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2018 at 6:45am |
|
the lever behind the fwwd/rev lever is not hooked up. not real sure what is suppose to go on it or where it is supposed to be hooked up. thanks to you all
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 41568
|
Post Options
Thanks(0)
Quote Reply
Posted: 12 Nov 2018 at 8:48am |
It is the throttle lever , would hook to injection pump or carb on gasser On diesel the throttle has a linkage that allows the foot control to decrease engine speed by retarding throttle setting Seems on a gas 2200 it would be the same as engine speed would be constant setting and slowed by foot pedal
Always seemed operating a HD4 the pedals were to close and somehow one foot got used to operate either right or left brake but somehow would end up with wrong foot in wrong place when needed
|
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
|
|
