| Author |
 Topic Search  Topic Options
|
Tracy Martin TN 
Orange Level Access
Joined: 11 Sep 2009
Location: Gallatin,TN
Points: 10630
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: The best mower deck spindle?
Posted: 27 Feb 2015 at 2:28pm |
|
Who has the best mower deck spindle? In ease of maintenance ,replacement and longevity for the cost? Thanks Tracy
|
|
No greater gift than healthy grandkids!
|
 |
|
Sponsored Links
|
|
|
Butch(OH)
Orange Level
Joined: 11 Sep 2009
Location: Lucerne Ohio
Points: 3834
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Feb 2015 at 3:45pm |
|
I like the spindles on our Scag and Bunton mowers. The spindles are hollow and use a long 5/8 bolt and nut to retain the blades instead of cap screws and common flat washers can be used if you lose the spacers some how. Bearings are common off the shelf too but in 10 years we have not had to change any.
|
|
Tracy Martin TN
Orange Level Access
Joined: 11 Sep 2009
Location: Gallatin,TN
Points: 10630
|
Post Options
Thanks(0)
Quote Reply
Posted: 27 Feb 2015 at 5:23pm |
|
Butch, the spindle assy for the 616-620 are about 400.00 each, less pulleys and bearings. I think I am going to make a new style like the Dixie Chopper uses.They look heavy and should last like the ones you mentioned. Thanks tracy
|
|
No greater gift than healthy grandkids!
|
|
Toscani NE SD
Orange Level
Joined: 21 Jan 2011
Location: Milbank S.D.
Points: 369
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Feb 2015 at 8:27am |
|
in my opinion u should never need a new spindle,my 620 which I bought used still has all original spindles everything is original no new bearings,if you grease them often u wont have any trouble,mine has mowed a lot of acres,i also have several large john deeres with 60" decks,never replaced a bearing yet,over 1300 hrs
|
|
Tracy Martin TN
Orange Level Access
Joined: 11 Sep 2009
Location: Gallatin,TN
Points: 10630
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Feb 2015 at 3:53pm |
|
That would be great, but mine had been abused before I got it. You sure don't want to buy any new ones, at the price they are now.
|
|
No greater gift than healthy grandkids!
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3552
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Feb 2015 at 4:45pm |
|
thats areal good question used ones i would probley rebiuld cast iron john deere huosings new ones just looking in the oregon catalog at new ones probley would order some for bobcat or exmark we sell a ton of the newer mtd and ayp spindles they are cheap but not very toughf
|
|
jaybmiller
Orange Level Access
Joined: 12 Sep 2009
Location: Greensville,Ont
Points: 22485
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Feb 2015 at 5:27pm |
|
One trick I picked up is to add a grease zerk( if not already there) and pop the 'dust shields' of the bearings to expose the race to the grease. Neighbour has 25 years service doing that. He also removes the spindle assemblies every fall, greases the nuts/bolts holding them onto the deck. 'Old school' stuff....
sure wish I could get $400 for a spindle !!
heck I'd settle for $200....
Jay
|
|
3 D-14s,A-C forklift, B-112
Kubota BX23S lil' TOOT( The Other Orange Tractor)
Never burn your bridges, unless you can walk on water
|
|
Coke-in-MN
Orange Level Access
Joined: 12 Sep 2009
Location: Afton MN
Points: 41604
|
Post Options
Thanks(0)
Quote Reply
Posted: 28 Feb 2015 at 5:50pm |
|
Swisher mower I have the deck bearings went out , found they used sealed bearings but not shielded = so I replaced with sealed and shielded bearings - was thinking of adding grease zerk to space and pulling the inside seals but figured 4 years service on first set - so should last about the same or longer this time around .
|
|
Faith isn't a jump in the dark. It is a walk in the light. Faith is not guessing; it is knowing something.
"Challenges are what make life interesting; overcoming them is what makes life meaningful."
|
|
