![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Side Draft Carb Performance? |
Post Reply ![]() |
Author | |
Zyta ![]() Orange Level ![]() ![]() Joined: 19 Jan 2010 Location: Ontario Points: 238 |
![]() ![]() ![]() ![]() ![]() Posted: 02 Apr 2010 at 12:29pm |
This carb is off a 410 Massey Combine and its a Marvel Schebler (Two Barrel Side Draft) used to fuel the 292 chev engines in the 410 combines. I would think these carbs would perform well on a 226 or 262 for pulling. The linkage swithes easily and the adapter off the combine from the carb to the manifold lets you flip it over and bolt it up to the intake. I am thinking of trying this on my 262 WD-45 versus using the old Zenith up draft ( any thougths or advise out there would be apprciated!) |
|
![]() |
|
Sponsored Links | |
![]() |
|
Zyta ![]() Orange Level ![]() ![]() Joined: 19 Jan 2010 Location: Ontario Points: 238 |
![]() ![]() ![]() ![]() ![]() |
Has anyone used one of these carbs or knows anything about them..they must have produced some good air and fuel mixture for a chev 292. Not sure what kind of cfm this carb would produce.
|
|
![]() |
|
Gerald J. ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: Hamilton Co, IA Points: 5636 |
![]() ![]() ![]() ![]() ![]() |
You could guess on the maximum flow that 292 might produce. Say figure 4000 rpm, takes two revolutions to ingest a theoretical 292 cubic inches. So you ingest (with no flow losses which isn't a possible condition) 2000 x 292 or 584,000 cubic inches per minute. There are 1728 cubic inches to the cubic foot so that's about 340 cfm.
I'd like three to put on the three siamezed ports on my gas 4020 and to have a vacuum advance port to improve its part throttle fuel economy. Get rid of that yard long intake manifold condensing gas on the way to the end cylinders too. Gerald J. |
|
![]() |
|
mlpankey ![]() Orange Level ![]() Joined: 13 Sep 2009 Location: Vols country Points: 4580 |
![]() ![]() ![]() ![]() ![]() |
At how many hg of mercury you suppose it would take to flow 340 cfm on that carb in the pic .
|
|
![]() |
|
Gerald J. ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: Hamilton Co, IA Points: 5636 |
![]() ![]() ![]() ![]() ![]() |
Probably no less than 30" Hg vacuum with a 15 psi boost on the air cleaner side.
Gerald J. |
|
![]() |
|
mlpankey ![]() Orange Level ![]() Joined: 13 Sep 2009 Location: Vols country Points: 4580 |
![]() ![]() ![]() ![]() ![]() |
wow i dont think that would run my weedeater. I was thinking 1.5to 5 "hg
|
|
![]() |
|
Zyta ![]() Orange Level ![]() ![]() Joined: 19 Jan 2010 Location: Ontario Points: 238 |
![]() ![]() ![]() ![]() ![]() |
So Mitch, are you saying this carb is better or worse than the big old Zenith Carb that came on the 262 combine engine? I was hoping it might be an improvement.
|
|
![]() |
|
Gerald J. ![]() Orange Level ![]() Joined: 12 Sep 2009 Location: Hamilton Co, IA Points: 5636 |
![]() ![]() ![]() ![]() ![]() |
Realistically, its probably more like a 250 cfm carburetor anyway.
Gerald J. |
|
![]() |
|
Jeff Z. NY ![]() Orange Level ![]() Joined: 11 Sep 2009 Points: 7326 |
![]() ![]() ![]() ![]() ![]() |
It doesn't hurt to try it.
|
|
![]() |
|
Zyta ![]() Orange Level ![]() ![]() Joined: 19 Jan 2010 Location: Ontario Points: 238 |
![]() ![]() ![]() ![]() ![]() |
Yes I think its worth a try..it's a more modern type of carb and I like the fact it's a side draft and a two barrel. |
|
![]() |
|
mlpankey ![]() Orange Level ![]() Joined: 13 Sep 2009 Location: Vols country Points: 4580 |
![]() ![]() ![]() ![]() ![]() |
Jim I dont know what it will flow . I do know that modern sized down drafts are figured at 1.5 and the old up drafts were figured at 5 "hg .
|
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |