This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity.
The Forum Parts and Services Unofficial Allis Store Tractor Shows Serial Numbers History
Forum Home Forum Home > Other Topics > Pulling Forum
  New Posts New Posts
  FAQ FAQ  Forum Search   Events   Register Register  Login Login


226 260 cid setup

 Post Reply Post Reply
Author
Message
wi50 View Drop Down
Orange Level
Orange Level


Joined: 24 Sep 2010
Location: weegieland
Points: 1010
Post Options Post Options   Thanks (0) Thanks(0)   Quote wi50 Quote  Post ReplyReply Direct Link To This Post Topic: 226 260 cid setup
    Posted: 17 Jan 2013 at 9:16pm
I have a cheap and easy parts setup I'd like to sell for someone looking to do a little upgradeing without breaking the bank or working to hard to do it. 
 
Set of 4 IH 308 truck engine rods, 4.185 bore Keith Black KB194 .060 over pistons and rings.  2 pistons brand new, 2 slightly used (neighbor had bought 8 and had 6 of them in his 6 cyl tractor engine for a bit) 
 
Works out to bore a set of 4 1/8 bore liners .060 over and offset grind the 4.5 stroke crankshaft to a 4.75 stroke.  You get a 4.185 bore X 4.75 stroke engine at 10.5 to 1 compression ratio. 
 
The rods are 8.5625" long center to center,  use a 2.125" diameter crankpin and are wide enough to fit the Allis crankpin.  The wrist pins in the IH are .925" and the pistons are .927".  I have honed the wrist pin bushings to size and resized the bottom end of the rods so they are ready to go.
 
$300 for the rods, pistons, rings, wrist pins and new spriol locks shipped to you. 
 
I do have nice used 4 1/8 liners available at additional cost, but I'd prefer to keep them.  Approxamate cost to bore and hone the liners is $100-$125, offset grind the 4 cyl crank $250.
 
"see what happens when you have no practical experience doing something...... you end up playing with calculators and looking stupid on the internet"
Back to Top
Sponsored Links


Back to Top
Charlie175 View Drop Down
Orange Level
Orange Level


Joined: 11 Sep 2009
Location: Shenandoah, VA
Points: 6358
Post Options Post Options   Thanks (0) Thanks(0)   Quote Charlie175 Quote  Post ReplyReply Direct Link To This Post Posted: 18 Jan 2013 at 6:25am
what kind of power output would this give?
Charlie

'48 B, '51 CA, '56 WD45 '61 D17, '63 D12, '65 D10 , '68 One-Ninety XTD
Back to Top
nborga87 View Drop Down
Silver Level
Silver Level
Avatar

Joined: 08 Jun 2010
Location: cordova, md
Points: 115
Post Options Post Options   Thanks (0) Thanks(0)   Quote nborga87 Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2013 at 12:14am
do you still have these parts?
Back to Top
wi50 View Drop Down
Orange Level
Orange Level


Joined: 24 Sep 2010
Location: weegieland
Points: 1010
Post Options Post Options   Thanks (0) Thanks(0)   Quote wi50 Quote  Post ReplyReply Direct Link To This Post Posted: 29 Mar 2013 at 12:47pm
Yes, I still have them, allong with bored sleves with new o-rings.  Also a 5.75 stroke crank and 8" billet rods for another combo.
715-790-1869
"see what happens when you have no practical experience doing something...... you end up playing with calculators and looking stupid on the internet"
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.10
Copyright ©2001-2017 Web Wiz Ltd.

This page was generated in 0.063 seconds.


Help Support the
Unofficial Allis Forum