| Author |
 Topic Search  Topic Options
|
Brad1 
Bronze Level
Joined: 22 Sep 2025
Location: Sparta MI
Points: 17
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: D15 Power Director
Posted: 10 hours 18 minutes ago at 6:30am |
|
|
 |
|
Sponsored Links
|
|
|
Brad1
Bronze Level
Joined: 22 Sep 2025
Location: Sparta MI
Points: 17
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 hours 11 minutes ago at 6:37am |
I This is what I found when I removed the side inspection cover. The small broken cast part worries me most. I'll have to use my bore scope to try and find where it came from, any guesses? One nut is missing, and the threads are pulled on the bolt it came from. My service manual doesn't seem to show the broken pieces of a circular Shim, if that is what it is. I use the tractor without the PD but would be nice if it did work. I removed one woodruff key from the shaft and one I found lying at the bottom. All experienced opinions are very welcome! and thanks for your time
Edited by Brad1 - 10 hours 3 minutes ago at 6:45am
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21995
|
Post Options
Thanks(0)
Quote Reply
Posted: 10 hours 3 minutes ago at 6:45am |
|
Shift transmission into neutral and the hand clutch into neutral and turn the assembly by hand to view things.
|
|
snowman(MI)
Silver Level
Joined: 12 Sep 2009
Location: Sand Lake, MI
Points: 375
|
Post Options
Thanks(0)
Quote Reply
Posted: 8 hours 52 minutes ago at 7:56am |
Been into that same situation a couple of years ago. I had a terrible clatter, power director didn't feel right. Took the inspection plate off and found some pieces. Ended up having to replace the yoke on the power director as an ear broke off. I'm not to far from you as I'm located in Sand Lake, MI. Here is a picture of my carnage that I had to address. PM if you want to talk more about this, I'll share my cell number. 
|
|
1950 WD, 1966 D-10 III, 1961 D-10 II, 1966 D-15 II Gas, A-C Minibike, 917 Hydro Mower, 917 Hydro Blower w/cab, West Michigan "Allis Express"
|
|
Brad1
Bronze Level
Joined: 22 Sep 2025
Location: Sparta MI
Points: 17
|
Post Options
Thanks(0)
Quote Reply
Posted: 6 hours 57 minutes ago at 9:51am |
|
Boy there's an offer I can't refuse and just a few miles away. I will PM you and thanks!
|
|
Brad1
Bronze Level
Joined: 22 Sep 2025
Location: Sparta MI
Points: 17
|
Post Options
Thanks(0)
Quote Reply
Posted: 6 hours 56 minutes ago at 9:52am |
|
OK, I'll give that a try and thank you
|
|
DSeries4
Orange Level
Joined: 12 Sep 2009
Location: Ontario, Canada
Points: 7511
|
Post Options
Thanks(0)
Quote Reply
Posted: 1 hour 56 minutes ago at 2:52pm |
|
Split the tractor and take the assembly out. Someone here should have a used assembly with all the parts you need. Also a good opportunity to clean the dirt and debris from between the clutch plates. Put everything back together as indicated in the service manual and it will be as good as new.
|
|
'49 G, '54 WD45, '55 CA, '56 WD45D, '57 WD45, '58 D14, '59 D14, '60 D14, '63 D15D, '66 D15II, '66 D21II, '67 D17IV, '67 D17IVD, '67 190XTD, '73 620, '76 185, '77 175, '84 8030, '85 6080
|
|
Brad1 wrote: