| Author |
 Topic Search  Topic Options
|
JPatten71 
Bronze Level
Joined: 03 Apr 2017
Location: Helena, Montana
Points: 48
|
 Post Options
 Thanks(0)
 Quote  Reply
 Topic: CA tractor, and 80R
Posted: 19 hours 46 minutes ago at 9:09pm |
|
I have CA that I'm trying to mount a 80R to the back. I bought the manual but it doesn't show pictures whit a ca so was wondering if anyone had one that they could take pictures of? Thanks in advance
|
|
Model CA, All Crop 60, Roto Baler
|
 |
|
Sponsored Links
|
|
|
DrAllis
Orange Level Access
Joined: 12 Sep 2009
Points: 21112
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 hours 36 minutes ago at 10:19pm |
|
I don't know if a CA would handle that mower ??
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8536
|
Post Options
Thanks(0)
Quote Reply
Posted: 18 hours 7 minutes ago at 10:48pm |
|
Do you have correct mounting brackets. Parts book shows which brackets for ca
|
|
HudCo
Orange Level
Joined: 29 Jan 2013
Location: Plymouth Utah
Points: 3687
|
Post Options
Thanks(0)
Quote Reply
Posted: 7 hours 23 minutes ago at 9:32am |
|
my mower for the wd has a mount that goes were the drawbar pins its areal heavey mower
|
|
PaulB
Orange Level
Joined: 12 Sep 2009
Location: Rocky Ridge Md
Points: 4885
|
Post Options
Thanks(0)
Quote Reply
Posted: 7 hours 15 minutes ago at 9:40am |
 DrAllis wrote:
I don't know if a CA would handle that mower ?? |
The CA is plenty of tractor to handle an 80R mower. Thinking otherwise is like thinking you need a 100+HP tractor to pull a hayrake. I've mowed more acres than I care to remember with an 80R on a CA tractor. The proper brackets are needed. If you manual doesn't have the mounting pictures for the CA tractor, the D12 and CA share all the same mounts, which are different than any other tractors. The D10 will share the CA/D12 drawbar mount but uses a different balance bar mount.
|
|
If it was fun to pull in LOW gear, I could have a John Deere.
Real pullers don't have speed limits.
If you can't make it GO... make it SHINY
|
|
JPatten71
Bronze Level
Joined: 03 Apr 2017
Location: Helena, Montana
Points: 48
|
Post Options
Thanks(0)
Quote Reply
Posted: 6 hours 43 minutes ago at 10:12am |
|
Thank you all for the response, I do have the one bracket for under the tractor but I think it's not a ca bracket. I'm willing to weld up what ever I need to just don't know where it should attach.
I bought the mower a 3 bottom plow and a 8 ft duck foot plow form a guy for $50 guy got it with his property and had no idea what it was 😂. The tractor my grandfather gifted to me for my highschool graduation. I bought the mower not knowing that he actually had a 80t mower he uses to have back in the day. So I want to get this on the CA to make a good pair
|
|
Model CA, All Crop 60, Roto Baler
|
|
Mikez
Orange Level Access
Joined: 16 Jan 2013
Location: Usa
Points: 8536
|
Post Options
Thanks(0)
Quote Reply
Posted: 6 hours 2 minutes ago at 10:53am |
|
I’ll look later but the operators manual should show how to mount it. The parts book shows the different brackets needed
|
|
Gary
Orange Level Access
Joined: 13 Sep 2009
Location: Peterborough,On
Points: 5765
|
Post Options
Thanks(0)
Quote Reply
Posted: 5 hours 50 minutes ago at 11:05am |
Here is a link to a 4 minute Video of a NF CA mowing with an 80R. Enlarge the Picture and stop the Video at the 1.0 minute mark for a rear view. This is a later Model CA with the new Snap Coupler set up. This may be required because the Mower Mounting Bracket normally gets installed on the Tractor in place of the Drawbar. Is your Rear Axle Hand Clutch functional because that would be a handy feature with the mower. G https://www.youtube.com/watch?v=_RPkaoPONT4
|
|
