This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
D21 Differential |
Post Reply |
Author | |
PDehring
Bronze Level Joined: 06 Jun 2018 Location: Central MI Points: 96 |
Post Options
Thanks(0)
Posted: Yesterday at 11:56am |
I have a D21 that doesn't want to turn, even with using the brakes. I'm suspecting the differential has become locked. I was wondering if anyone has experienced this and what the cause was.
I haven't torn into it yet but was looking for any info before I do.
|
|
1937 M Crawler, 1963 D21, 1964 D21, 1965 D12 SIII, 1970 220, 1976 185
|
|
Sponsored Links | |
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20486 |
Post Options
Thanks(0)
|
Been there done that. Low transmission/rear end oil levels (all one compartment) is for sure the death of a differential located that high in the drive line. A tractor used for moldboard plowing would have the highest failure rate possibility. Four new matching radial tires across the back and a lot of short turning would be stressful. A tractor that weighed more than 13K would also place the differential under more pressure. I remember a customer who once got one buried in the mud and rocked it back and forth and back and forth while jamming on the brakes side to side. Soon afterwards the differential was toast. What's the history of the tractor ??? I've always looked back to a D-17 or WD-45 and think of the hundreds upon thousands of hours some of those tractors had on a moldboard plow and NEVER had any differential issues.
Edited by DrAllis - 16 hours 39 minutes ago at 6:00am |
|
PDehring
Bronze Level Joined: 06 Jun 2018 Location: Central MI Points: 96 |
Post Options
Thanks(0)
|
Thanks Dr. I'm not sure on the history of it, I got it last year after it had been sitting in a barn for 20+ years. It does have 24.5x32s that are half loaded. The rear end does have enough oil (plenty on the dipstick) but who knows what the tractor was put through in the last 60 years.
|
|
1937 M Crawler, 1963 D21, 1964 D21, 1965 D12 SIII, 1970 220, 1976 185
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20486 |
Post Options
Thanks(0)
|
One last thing that I forgot.......160 HP fuel setting versus 127.75 HP fuel setting also stresses the differential more.
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8239 |
Post Options
Thanks(0)
|
Is the 220 stouter in that area?
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20486 |
Post Options
Thanks(0)
|
210-220's used the same differential. They had a larger bearing on the ring gear side of the diff where the D-21 was same bearing on both sides. 210-220's were way heavier in the final drive/bull gear and axle size area. The wheelbase was even 4 or 5 inches longer because of the larger diameter bull and bull pinion gears.
|
|
injpumpEd
Orange Level Access Joined: 13 Sep 2009 Location: Walnut IL Points: 4911 |
Post Options
Thanks(0)
|
Not to argue with Dr, he's forgotten more than I'll ever know. But, the 210 rearend I just rebuilt a few months ago had the same diff carrier bearings on both sides, and looking at parts books, the D21 also used the same cups and cones as 210 & 220. As to the op, guessing you have a galled up differential assembly, with a permanent diff lock lol!
|
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20486 |
Post Options
Thanks(0)
|
I might have confused myself with the 4-pinion's on 190's and 200's. I know they had a bigger bearing on the right side, and for some reason I thought the 210/220 series did too.
|
|
SteveM C/IL
Orange Level Access Joined: 12 Sep 2009 Location: Shelbyville IL Points: 8239 |
Post Options
Thanks(0)
|
My 220 has been relegated to planter and Bush hog so it might be OK at 170.
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |