This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
7010 injector pump |
Post Reply |
Author | |
farmboycitygirl
Bronze Level Joined: 16 Feb 2010 Location: 66528 Points: 115 |
Post Options
Thanks(0)
Posted: 15 Oct 2024 at 6:49pm |
Our 7010s injector pump managed to come apart (literally). We have another running engine out of a combine however the injector pump is an inline not the circular rosa master. It has Minimec pump (that what the pump says anyway. My question is will this injector pump replace our existing 7010 rosa master pump if we can change the pump what needs to be done or should we replace the entire engine with the combine engine?
|
|
Sponsored Links | |
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20481 |
Post Options
Thanks(0)
|
I don't know what has failed in your injection pump, but I would never advise swapping a (good?) running engine for some 10 year older and unknown condition combine engine. Fix your pump or buy a used pump from a salvage yard and have it freshened up. A pump from a 7000-7010-7020 or M2/M3 combine will fit.
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20481 |
Post Options
Thanks(0)
|
From a labor standpoint, an injection pump swap is a couple of hours and takes minimal tools. An engine swap from a combine ?? waaaay more labor than you can imagine by comparison.
Edited by DrAllis - 16 Oct 2024 at 6:28am |
|
injpumpEd
Orange Level Access Joined: 13 Sep 2009 Location: Walnut IL Points: 4909 |
Post Options
Thanks(0)
|
I cannot imagine how bad a Roosa DM could fail to make swapping the entire fuel system or even engine over to get it going. Sometimes you just have to bite the bullet and call in a professional lmao! Most pump shops have good cores to scavenge parts from to make one run again!
|
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
darrel in ND
Orange Level Joined: 22 Nov 2009 Location: Hebron, ND Points: 8633 |
Post Options
Thanks(0)
|
I'm no expert, but will chime in. Mostly curious as to what could have possibly happened to your roosa pump to make it unrepairable? I do know for certain that getting a roosa back on there, whether it's having yours repaired by a good pump shop, or finding a different one like it, will definitely be best route to go, like Dr and Ed said.
Darrel |
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20481 |
Post Options
Thanks(0)
|
Seems like I remember this tractor having hard starting issues some time back and pump timing was in question. I thought the pump had been just gone thru at that time ?? Maybe not.
|
|
Straanger
Bronze Level Joined: 10 Dec 2019 Location: Michigan Points: 38 |
Post Options
Thanks(0)
|
“Managed to come apart (literally)”.
Sounds like something that should be explained. Preferably with pictures. |
|
farmboycitygirl
Bronze Level Joined: 16 Feb 2010 Location: 66528 Points: 115 |
Post Options
Thanks(0)
|
something came loose and punched a hole in the case.
|
|
farmboycitygirl
Bronze Level Joined: 16 Feb 2010 Location: 66528 Points: 115 |
Post Options
Thanks(0)
|
Yes DR it is the same tractor - we had the pump rebuilt by ST Joe diesel in St Joe MO. The warranty was only a year so we got a used pump and that one is the one that flew a part.
|
|
HudCo
Orange Level Joined: 29 Jan 2013 Location: Plymouth Utah Points: 3536 |
Post Options
Thanks(0)
|
still dont think i would change out the engine just for a bad pump un less you think their is somthing wrong with accessory drive
|
|
injpumpEd
Orange Level Access Joined: 13 Sep 2009 Location: Walnut IL Points: 4909 |
Post Options
Thanks(0)
|
possibly could use both pumps to build one good one again.
|
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
injpumpEd
Orange Level Access Joined: 13 Sep 2009 Location: Walnut IL Points: 4909 |
Post Options
Thanks(0)
|
well, I got the St Jo pump in and apart, sadly the head is seized. The leaf spring screws had backed out quite a ways(had to be really low on hp) to the point one of them began hitting the lobes of the cam ring. So with any internal unhappiness, they end up seizing up. It looks like the cam ring had been replaced as well as the head and rotor being a rebuilt one by the looks of things. The DM pumps use shoes that are .005" difference in sizes, and a lo hp app like a 7010 would use -020 shoes, that keeps the leaf spring screws in most of the way letting their nylok patch hold them in place. Well, this one has new looking -015 shoes so in order to close down the roller setting the leaf spring screws would be out further, therefore allowing them to simply back out. I texted Gary some pics, so hopefully he can post them up, I am not smart enough lmao! Sad to see the poor work coming out of the big shops, and they won't back it. This had to be making horrendous racket while the screw was hitting the cam lobes, could have saved the head if it would have been parked and pulled off before catastrophic failure. Looked closer and it has -010 shoes which is even worse. Almost like they only want to stock the one size. The leaf spring screws are loose, the one that hit the lobes turns with my fingers.
Edited by injpumpEd - 11 Nov 2024 at 7:46am |
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
DrAllis
Orange Level Access Joined: 12 Sep 2009 Points: 20481 |
Post Options
Thanks(0)
|
To quote Mr. Spock: "interesting"..................
|
|
Amos
Orange Level Joined: 11 Sep 2009 Location: Ontario Points: 1316 |
Post Options
Thanks(0)
|
Ed, I just want to say thank you for posting up what happened. I have been misled by so many injection pump shops in my life. I really appreciate that you are honest on here and give proper advice. I sure wish you lived close enough to me I could drive up to your door with my pumps and injectors.
Its hard to have faith in shops when you post that they used the wrong parts and that they assembled it so the screws could come loose. Almost makes a guy wonder if it was the first one they ever worked on and they never read the spec sheet how to assemble
|
|
farmboycitygirl
Bronze Level Joined: 16 Feb 2010 Location: 66528 Points: 115 |
Post Options
Thanks(0)
|
|
|
farmboycitygirl
Bronze Level Joined: 16 Feb 2010 Location: 66528 Points: 115 |
Post Options
Thanks(0)
|
|
|
farmboycitygirl
Bronze Level Joined: 16 Feb 2010 Location: 66528 Points: 115 |
Post Options
Thanks(0)
|
|
|
farmboycitygirl
Bronze Level Joined: 16 Feb 2010 Location: 66528 Points: 115 |
Post Options
Thanks(0)
|
|
|
injpumpEd
Orange Level Access Joined: 13 Sep 2009 Location: Walnut IL Points: 4909 |
Post Options
Thanks(0)
|
Thanks Gary for getting the pics up. Hopefully your other pump that flew apart will have a good head & rotor in it. I have a new h&r in stock and warehouse has several too, but the $1600 price tag stings! There's lots of these DM pumps around to steal parts out of yet.
You can see the screw is worn down on top, and the notch in the center of the cam lobe is from it wearing on it. Any side load on the rotor will cause it to seize. This could possibly have been saved if it was noticed to be making more noise than normal. I'd never seen this before, so I would not have guessed this was happening. Edited by injpumpEd - 16 hours 12 minutes ago at 8:53am |
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |