This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | ||||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Legacy Parts |
Post Reply |
Author | |
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
Posted: 01 Aug 2024 at 6:03am |
Looking for the PTO drive sheave, and deck driveshaft for an early 90's Legacy. This one has a 3cyl Daihatsu diesel engine and runs very well so worth repairing. This style setup was used only on the Legacy series and the shaft is still available, but the sheave is long discontinued. The keyway is chewed out of each part. If someone has one of these to part out I'd entertain making purchase; otherwise I'll drop them at a friend's machine shop and he'll open up and bush the cast iron sheave, and broach a new keyway in the bushing. Will also flip the shaft and machine in a new "Woodruff" keyway. PM me if anything is available. Thanks, Photo shows the breakdown and I' m needing parts referenced as #11, and 12: |
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Sponsored Links | |
im4racin
Orange Level Joined: 12 Jun 2017 Location: Garrison ND Points: 931 |
Post Options
Thanks(0)
|
Get the update kit with the new shaft. If pulley bore isnt wore take to machine shop and have a new key way cut in a 1/3 of a turn from the original. i also have added set screws to keep tight
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
Yes, thank you. Pulley bore is destroyed and will be bushed/sleeved with new keyway machined. Updated shaft is available at great cost for what it is. Support bearings are also worn elliptical.
Came to me with a vibration complaint. Thanks,
Edited by Codger - 01 Aug 2024 at 7:59am |
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Mikez
Orange Level Access Joined: 16 Jan 2013 Location: Usa Points: 8348 |
Post Options
Thanks(0)
|
Have any part numbers. Part number for update kit to.
|
|
im4racin
Orange Level Joined: 12 Jun 2017 Location: Garrison ND Points: 931 |
Post Options
Thanks(0)
|
The update is a longer shaft and the axle pivot tube changes too. The tube has flanges. It is worth the update if the shaft has worn into the pivot.
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
This one fortunately has not worn that far. The bearings appear to have been replaced but a snap ring was not in place allowing the sheave to "walk" on the shaft destroying both parts.
|
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Matt Tallant
Orange Level Joined: 15 Aug 2011 Location: Virginia Points: 670 |
Post Options
Thanks(0)
|
That’s the main reason I sold my early Legacy is because parts availability Steering sector worn out and slot of the parts were NLA
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
Customer dropped this off as it kept breaking the belt tension springfor the PTO deck driving belts. After replacing the tensioner, spring, bushings, sleeve, and mounting hardware to build it back up and actually ascertain what was wrong, this is what I found. The video is taken is slow motion and the engine is running at high idle: https://www.youtube.com/shorts/E7a-WN1S5YY Here is the original installation of the front sheave: There is supposed to be a snap ring in front of the flat washer retaining the sheave to the shaft. This is the shaft after the sheave was pried free: This is the rear of the sheave: Another view of the shaft damage in the keyway area: I put the shaft and sheave through the blast cabinet prior to dropping at the machine shop yesterday afternoon but didn't photo that. That gives him something clean to work with. He is going to bore the sheave, sleeve it down and two set screws to lock the busing into place. The shaft will either have a new Woodruff key, or could be a simple straight keyway milled back into it. Hope to pick the parts up on Monday. The shaft is still available new but the sheave is long discontinued. Not been able to locate one used either as it was only used on the Legacy series. New PTO shaft support bearings have shipped so when going back together all will be in good condition for hopefully years of good service.
|
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
Back together without problems. Owner picking up this evening and get to mowing.
|
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
Owner has decided to retain his Sunstar. So happy with his diesel Legacy we worked with he now is going to keep this one for his son. This is an NOS 54" deck that has never been built up but the paint was falling off of it so I blasted it clean this morning along with a couple other small items: I'll drag a 180 grid disc on a D/A sander over the surface and repaint it. Has all new quills and bearings, along with a roller bar and rollers to be installed also; so should be just about as good as new.
|
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
IBWD MIke
Orange Level Joined: 08 Apr 2012 Location: Newton Ia. Points: 3684 |
Post Options
Thanks(0)
|
That is going to be sweet! Would love to find a deck like that, for just about anything.
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
Original deck panels that cover the sheaves and belts which are getting rough on the Simplicity SunStar mower: A few minutes later: There is some pitting which is to be expected but no blow through at all. Panels are still good and solid. A polyester high build primer will fill these easily and be durable. I'll get these in epoxy prime coat tomorrow morning to keep the process moving along. Got a lot to do before harvest and not a lot of time to do it. |
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
Time for some orange paint: Shiny enough: |
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Steve in NJ
Orange Level Access Joined: 12 Sep 2009 Location: Andover, NJ Points: 11776 |
Post Options
Thanks(0)
|
Lookin' nice! Ya need sunglasses on to see those. Whew! Steve@B&B
|
|
39'RC, 43'WC, 48'B, 49'G, 50'WF, 65 Big 10, 67'B-110, 75'716H, 2-620's, & a Motorhead wife
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
Thanks Steve. Those are photographed "wet" and the paint has yet to flow out. I let them set in the booth overnight and they look a bit more slick in the morning. Owner is going to be kicking himself for disallowing me to finish out the pitting depressions from the rust; although they are minor as I pretty much buried them in undercoat(s). However, it is just a lawnmower. Probably going to refinish the SunStar mower also given this looks so nice.
|
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Codger
Orange Level Joined: 23 Dec 2020 Location: Illinois Points: 2032 |
Post Options
Thanks(0)
|
Ordered all new fasteners to reassemble the deck which will probably be after harvest. Some of the original is very corroded so not going to bother with clean up but rather replace.
|
|
A career built on repairing and improving engineering design deficiencies, shortcomings, and failures over 50 years now.
|
|
Matt Tallant
Orange Level Joined: 15 Aug 2011 Location: Virginia Points: 670 |
Post Options
Thanks(0)
|
I have a nice deck gear box from Sunstar if any one needs it let me know
|
|
Post Reply | |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |