![]() |
This site is not affiliated with AGCO Inc., Duluth GA., Allis-Chalmers Co., Milwaukee, WI., or any surviving or related corporate entity. All trademarks remain the property of their respective owners. All information presented herein should be considered the result of an un-moderated public forum with no responsibility for its accuracy or usability assumed by the users and sponsors of this site or any corporate entity. | |||||
The Forum | Parts and Services | Unofficial Allis Store | Tractor Shows | Serial Numbers | History |
Metal hydraulic lines on a 220 |
Post Reply ![]() |
Author | |
Kevin210 ![]() Silver Level ![]() Joined: 08 Oct 2018 Location: Indiana Points: 370 |
![]() ![]() ![]() ![]() ![]() Posted: 16 Jun 2024 at 8:23pm |
Would ANYONE happen to have the four steel
hydraulic lines for a 220 that run under the fuel tank.I would love to have 4 good ones. Thanks. |
|
![]() |
|
Sponsored Links | |
![]() |
|
Mikez ![]() Orange Level Access ![]() ![]() Joined: 16 Jan 2013 Location: Usa Points: 8204 |
![]() ![]() ![]() ![]() ![]() |
Are the 253825,253826
|
|
![]() |
|
Kevin210 ![]() Silver Level ![]() Joined: 08 Oct 2018 Location: Indiana Points: 370 |
![]() ![]() ![]() ![]() ![]() |
I don't know part numbers.
There are only 4 lines that go to the back. I would just like to have 4 that aren't rusty/rusted or all bent up.. |
|
![]() |
|
injpumpEd ![]() Orange Level Access ![]() ![]() Joined: 13 Sep 2009 Location: Walnut IL Points: 4802 |
![]() ![]() ![]() ![]() ![]() |
I took 2 minutes and looked, the numbers Mike lists do appear to be the 4 that got to the remote couplers, on one type. Kevin, you need to go on agco partsbooks and decide which ones you need. There's probably some around off of pullers too, and rock valley salvage, and others.
|
|
210 "too hot to farm" puller, part of the "insane pumpkin posse". Owner of Guenther Heritage Diesel, specializing in fuel injection systems on heritage era tractors. stock rebuilds to all out pullers!
|
|
![]() |
|
Michael V (NM) ![]() Orange Level Access ![]() Joined: 12 Sep 2009 Location: NM Points: 2366 |
![]() ![]() ![]() ![]() ![]() |
I've tried to find them, called several salvage yards,tried agco, with no luck, gave up and just replaced with hoses
|
|
![]() |
|
Mikez ![]() Orange Level Access ![]() ![]() Joined: 16 Jan 2013 Location: Usa Points: 8204 |
![]() ![]() ![]() ![]() ![]() |
I looked again and realized there not what Kevin is looking for
|
|
![]() |
|
Acdiesel ![]() Orange Level ![]() ![]() Joined: 15 Jun 2012 Location: Rochester Ohio Points: 2527 |
![]() ![]() ![]() ![]() ![]() |
I needed some for my D21 that I'm restoring and I wanted it back to factory parts and couldn't find them so I made my own. My original ones we just rusted out. but still had good shape, not bent.
I Just bought some tubing stock, got a pipe bender and bent them to look just like the original ones, cut the ends off the old tubes and just reused the original nut and backup ring. If your not the best at tube bending most hydraulic shops can bent them for you. just my experience. Dan
Edited by Acdiesel - 18 Jun 2024 at 11:04am |
|
D19 diesel,D17 diesel SER.3 D14 NF,D14 WF, D15 SER.II wf
D15 SER.2 DIESEL,D15 ser.II nf D12 SER.I, D10 Ser.II 2-720'S Gmc,caterpillar I'm a pharmacist (farm assist) with a PHD (post hole digger) |
|
![]() |
|
Kevin210 ![]() Silver Level ![]() Joined: 08 Oct 2018 Location: Indiana Points: 370 |
![]() ![]() ![]() ![]() ![]() |
You just have to laugh and shake your head at some point.
It's a long story. When I did my 210 the lines were still in great condition and straight like they're suppose to be. What happened was I hung them on a trash barrel to drain not thinking about the trash truck picking up trash. So the trash truck guy assumed they were trash and threw them in the truck and of course they ended up at the landfill,Yes I meet the driver there and went through the load as it dumped and found them but one was ruined. I tried to get a line made in my area but no one could make the short bend where they fit above the fuel tank but I did get lucky and found some back then. But these on the 220 look like a snake in the grass. It seems that the quick bend I call at the connections is what they couldn't get right or something. I just want some that are in good condition I can just hookup and go.. Sorry so long... |
|
![]() |
|
Kevin210 ![]() Silver Level ![]() Joined: 08 Oct 2018 Location: Indiana Points: 370 |
![]() ![]() ![]() ![]() ![]() |
I'll check with rock valley this weekend.
Thanks guys. |
|
![]() |
|
Acdiesel ![]() Orange Level ![]() ![]() Joined: 15 Jun 2012 Location: Rochester Ohio Points: 2527 |
![]() ![]() ![]() ![]() ![]() |
Wengers of Meyerstown list some on there web site, you will need to match part numbers.
Dan
|
|
D19 diesel,D17 diesel SER.3 D14 NF,D14 WF, D15 SER.II wf
D15 SER.2 DIESEL,D15 ser.II nf D12 SER.I, D10 Ser.II 2-720'S Gmc,caterpillar I'm a pharmacist (farm assist) with a PHD (post hole digger) |
|
![]() |
Post Reply ![]() |
|
Tweet
|
Forum Jump | Forum Permissions ![]() You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |